Question about 1999 Plymouth Grand Voyager

1 Answer

EGR valve erroe code P0401

Where is the egr valve on a 1999 voyager? and how do I clean it out?? can I clean it out and how to be sure it needs to be cleaned out or replaced????

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

Depending on what size engine you have, it's either down on the back side of the engine by firewall, ( you have to take intake breather off to get at it) or by or below the battery. Some of these cars don't have one, depending on the engine.

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Obd2 codes p0401 and p1744


P1744 -transmission intermittent/torque converter is a manufactures code;they have that problem,like the wipers coming on.
P0401-egr valve flow insufficient;replace or remove,spray B-12 on and around all openings;clean let dry new gasket.

Jun 28, 2012 | 1999 Mercury Sable

2 Answers

Have 1999 Mercury Sable and failed emissions for P0401 code, I replaced the EGR Valve and had the code reset, service engine light came on again Approx 15 miles later. Took it to Auto Zone and they gave...


I am not surprized. The chances that replacing an EGR valve will fix a code P0401 on ANY Ford vehicle is about 1/2 of 1 percent. You most likely either have clogged up EGR ports in your intake manifold, or you have a defective Delta Pressure Feedback EGR (DPFE) sensor.

To find out which it is, apply vacuum to the EGR valve vacuum port with the engine idling. The engine should stumble and/or stall. If it does not, your ports are clogged. If it does, the most likely cause of your problem is the DPFE sensor. However, the EGR vacuum control solenoid could also be the cause.
You cannot properly test the EGR vacuum control solenoid without the proper equipment, but you can check to make sure that there is manifold vacuum going into one side of the solenoid and you can check to make sure that there are no breaks or leaks in the line that runs between the solenoid and the valve. If you find any of these, repair as necessary. If you do not find a problem with the vacuum lines, then you can take a "guess" and replace the DPFE. If this does not work, then you can "guess" again and replace the solenoid. If it still does nort work, then you probably have a bad electrical circuit to the solenoid (once again, requiring the proper equipment to diagnose).

Please also review the following article: What Else Could Be Wrong?

Nov 18, 2011 | 1999 Mercury Sable

1 Answer

Service engien soon light on a 1999 buick century code 401pd


If the DTC is P0401 it means that the EGR Valve is clogged or air flow is insufficient.Take EGR valve off and clean carbon out or replace EGR valve with a new one.

Oct 28, 2011 | 1999 Buick Century

2 Answers

Fault code p0401


This error means Exhaust Gas Recirculation Flow Insufficient Detected.

You can deatils on the following site http://www.permoveo.ltd.uk/tabid/122/OBD-Error-Code/P0401/Diagnostics/Hyundai/Default.aspx

but for convenience I have reproduced that information here:
.
Generic OBD Error Code Details for P0401 Exhaust Gas Recirculation Flow Insufficient Detected What does this mean? OBD Code P0401refers to
EGR stands for Exhaust Gas Recirculation. It is part of the vehicle emmissions system, and is used to reduce combustion temperature and pressure to control Oxides of Nitrogen. There are generally three parts to the EGR system: the EGR valve, an actuator solenoid, and a differential pressure sensor EGR (DPFE). These things work together to deliver the correct amount of recirculation based on engine temperature, load, etc. The P0401 code means that OBD detected an insufficient amount of EGR. SymptomsPossible sumptoms of OBD code P0401
You may notice drivability problems such as pinging (a.k.a. pre-ignition knock) when the engine is under load or the vehicle is at higher speeds. There may also be other symptoms. CausesPossible causes of OBD code P0401
A code P0401 most likely means one or more of the following has happened: •The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced•There is a blockage in the EGR (tube), most likely carbon buildup •The EGR valve is faulty •The EGR valve may not be opening due to a lack of vaccuum Possible SolutionsIn fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit. •Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open •Clean out the EGR valve and/or tubing to remove deposits•Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)•Replace the DPFE sensor (with a good quality / OEM one)•Replace the EGR valve Related CodesP0400 P0402 P0403

Jul 12, 2011 | Hyundai Tucson Cars & Trucks

2 Answers

1999 mercury sable engine code p1744,p0401. Failed e check. EGR looks new, replaced egr solenoid then cleared codes. what more can i do about the p0401 code and the p1744 code Thanks


for p0401:
In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open.
Clean out the EGR valve and/or tubing to remove deposits.
Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model).
Replace the DPFE sensor (with a good quality / OEM one).
Replace the EGR valve.

Jul 08, 2011 | 1999 Mercury Sable

2 Answers

I have a code P0401. What is this and how can I fix it?


P0401 - Exhaust Gas Recirculation Flow Insufficient Detected

Possible causes - Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control valve stuck closed
- EGR volume control solenoid valve
- Dead (Weak) battery
- EGR passage clogged
- Exhaust gas leaks Possible solution - Clean EGR Valve
- Repair EGR harness or connector
- Replaced EGR volume control solenoid valve
- Replaced EGR volume control valve

Mar 20, 2011 | 1998 Ford Taurus

1 Answer

Ford Explorer : How to Troubleshoot the EGR P0401 Trouble Code


P0401 - Exhaust Gas Recirculation Flow Insufficient Detected

Possible Causes:
- Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control valve stuck closed
- EGR volume control solenoid valve
- Dead (Weak) battery
- EGR passage clogged
- Exhaust gas leaks
- Faulty EGR valve

Possible Solutions:
- Clean EGR Valve
- Replace EGR Valve
- Repair EGR harness or connector
- Replace EGR volume control solenoid valve
- Replace EGR volume control valve

Jan 24, 2011 | Ford Explorer Cars & Trucks

5 Answers

ENGINE RUNS FINE. SERVICE LIGHT IS ON AND THE CODE NUMBER SHOWING IS PO401. WHAT IS THIS FOR SAYING?


  1. po401 refers to an insuffient flow of EGR gasses
  2. locate egr valve
  3. with engine running at idle
  4. on the underside of the valve you can access the diaphram.
  5. wearing glove if ness
  6. lift diaphram while idling
  7. does engine stall or run very rough?
  8. if not remove valve
  9. start engine
  10. you should hear a very large vaccum leak and exhaust noise
  11. if either are missing investigate cause
  12. if ok reassemble.
  13. locate DPFE sensor
  14. inspect sensor for damage
  15. inspect hose to sensor for damage
  16. replace sensor
  17. 9ecffd7.gif

Aug 10, 2010 | 1999 Ford Taurus

3 Answers

CODE P0401 COMEING UP


I had an OBD II 401 code and fixed it by cleaning out the EGR vacuum line in the intake manifold. I removed teh EGR Valve and the set screw below it. i used a rifle cleaning brush and one length of the rod. Then I replaced teh set screw. I started teh engind and let the vacuum **** some carb cleaner through the front port hole. when it was sucking good I replaced teh EGR valve and reset the codes. That fixed it.8_26_2012_9_39_13_pm.jpg

Feb 12, 2010 | 1999 Isuzu Rodeo

1 Answer

Obd2 scanner code reader indicated a p0401 problem with my 1999 mercury sable. What could be wrong. According to the handbook that is given with the scanner p0401 is an egr with insufficient flow.


your egr valve may be bad or you mite be just clogged. take it off and see if there is any deris in egr vavle or the hole on to mounting service if so clean out. if not replace the egr valve.

Nov 16, 2009 | 1999 Mercury Sable

Not finding what you are looking for?
1999 Plymouth Grand Voyager Logo

Related Topics:

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...