Question about 2007 Saturn ION-2 Quad Coupe

Open Question

Iat location 2005 jeep grand cherokee limited 4.7L?

Iat sensor location on 2005 Jeep Grand Cherokee Limited 4.7L?

Posted by on

  • sam haddad Mar 10, 2009

    i have looked round and have found a plug type piece that goes from my air filter to intake air hose and then into what i believe it the throttle body. but it is a plug it comes of kinda like a wall outlet! the plug is located on my air intake hose!

  • yadayada
    yadayada May 11, 2010

    look in the air intake hose or the air cleaner box, the sensor is small and round with 2 wires going to it.

×

6 Suggested Answers

  • 323 Answers

SOURCE: Jeep Grand Cherokee Limited P0700 diagnostic problem

P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.

Posted on Jun 14, 2009

  • 43 Answers

SOURCE: Very rough idle on 2002 Jeep Grand Cherokee Limited Edition V8

If you haven't changed the plugs or had the fuel system cleaned, now would be a good time to do it. The number 1 culprit for rough idles is dirty injectors or plugs. You can try an injector cleaner in a can (or bottle) for under $10 and see if it helps, and then work from there. If there isn't any improvement then if you are able to, check the plugs for any gunky buildup and if you find a bad plug, make sure you replace them all (or have them replaced) at the same time.

Posted on Aug 03, 2009

  • 52 Answers

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Aug 11, 2009

  • 96 Answers

SOURCE: knocking in rear of 1995 jeep grand cherokee while

check rear suspension for any broken links

Posted on Sep 17, 2009

ZJLimited
  • 17970 Answers

SOURCE: 1996 Jeep Grand Cherokee window relay

Check in the Fuse Block, the cavity 2, fuse 30 Amp c/Brkr (Section (8W Page 7)

More details about electrical system for ZJ Grand Cherokee, you can find here: ZJ-Secc-8W-Wiring-Diagrams

I hope help you with this (rated this help). Good luck.

Posted on Sep 24, 2009

  • 6982 Answers

SOURCE: 2001 Jeep grand cherokee motor knock 4.7 motor

First, if the noise is from the upper part of the engine and is more of a tapping than a knock, likely you have a problem in the valvetrain, most often a bad lifter or worn rocker arm. If the noise is low, deep inside, the noise is from a bearing. This is generally accompanied by lower than normal oil pressure. Regardless of the underlying cause, correcting the cause will not stop the knock. To do that correctly, the engine needs to be removed and all crankshaft bearings and the crankshaft itself need to be replaced (crank can sometimes be "undercut" and thicker bearing shells can be used depending upon the amount of wear.) If caught very early, sometimes only one bearing can be replaced in-car, but in 99% of all cases I have ever seen, most will fail again, sometimes more severely if done this way.

Posted on Dec 10, 2009

Testimonial: "Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse Box


2005 Jeep Grand Cherokee Limited Fig. 8: Left Side Of Engine Compartment Courtesy of DAIMLERCHRYSLER CORP.

Jul 29, 2014 | 2005 Jeep Grand Cherokee

1 Answer

2008 Jeep Grand Cherokee Limited 5.7 Hemi Check engine light on, code P0750


2008 jeep cherokee (hemi) engine light its on i brought to fix they change 4 sensor and the converter. After 5 days engine light comes on again, what else can be? im depress about it, after paying almost 2 grand to fix this issue.

Jan 25, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Where is the IAT sensor on a 1999 jeep grand cherokee limited 4.7L


great question, on some cars, its NOT THERE.
nice how you actually state engine option.
but way not post symtoms, or evidence. (got DTC errors from scan tool?)
fsm says.
4.7 quote:
The Intake Manifold Air Temperature IAT sensor is located on the left side of the intake manifold.
For a temperature of 68F (20C) the resistance is approximately 6000 ohms. For a temperature of 104F (40C) the resistance is approximately 3300 ohms. (this forum hates degrees symbols , dang)

its just a Thermistor. NTC

on some cars, its in the MAF
others its screwed in to the air cleaner box.
others, (yours) its in the air plenum. (MAP base EFI)
the map system needs the plenum baro and temp. TOGETHER.

Nov 25, 2013 | 1999 Jeep Grand Cherokee Limited

1 Answer

Where is the camshaft sensor located on my 99 Jeep Grand Cherokee


If you still have a cap rotor and ignition wires, it's inside the distributor. If not, it is the part where the distributor used to be (center rear of the engine behind the intake manifold)

Feb 19, 2010 | 1999 Jeep Cherokee

2 Answers

My 2005 jeep grand cherokee limited uconnect on the rearview mirror dosent work, wondering what i can check to fix this


9 time out of 10 it is the phone not the Uconnect. Try to pair a different phone on the device then see what happens.

Oct 25, 2009 | 2006 Jeep Grand Cherokee

1 Answer

Where is the IAT sensor at in my 1997 Jeep Grand Cherokee Limited?


In the air box... should be a two wire plug:
- ZJ-Secc-25-Emission-Control-Systems
- ZJ-Secc-8W-Wiring-Diagrams (page 62)

Hope helped with this; good luck (remember rated this help).


Oct 23, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Message "Check gas cap" Grand Cherokee WK 2005 limited 4,7l


if the gas cap is on properly and the light is still on , then you need to replace it. the light means that there is gas vapor leaking from it

May 26, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Jeep Cherokee Limited


that sensor is part of the lift gate latch ...the whole assembly will need to be replaced

Sep 25, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2007 Saturn ION-2 Quad Coupe Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...