Question about 1994 Jeep Grand Cherokee

1 Answer

How to replace my 1994 jeep fog lamp? there are not enough space for the lamp plug go through. chris

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Allways you need removal the fog light.
Check this:
ZJ-Secc-8L-Lamps (Page 5, Fig. 4 - english)
ZJ-1993-Service-Manual-Secc-08L-Luces (Page 13, Fig. 1 - spanish)

In the second option you have better images.

Good luck!!!

Posted on Mar 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change fog light n lense


Remove the plastic screen surrounding the fog light (held on by 3 Torx screws). Elevate the front of the car and remove the plastic tray under the front bumper(held on by 5-6 eight mm headed sheet metal screws).
Unplug the wire to the lamp and remove the four screws holding the fog lamp on.(4 Torx screws). You can't get a screwdriver into this tight space, so you'll need a torx bit and a 1/4" drive ratchet to turn it.
It is a tight work area and you'll have to take your time and just "worry" those screws out with the Torx bit..
Remove the lamp unit and replace it with the new one. reinstall four screws. Plug wire into the new lamp. Then reinstall the plastic splash tray under the bumper and the wire grill around the light. Done!

Mar 02, 2013 | 2008 Mercedes-Benz Mercedes Benz C Class

1 Answer

I have a 2001 jeep grand Cherokee Laredo that did not come with fog lights but has the plugs for the bulbs. I purchased the fog lights plugged them in but they didn't turn on. I was wondering if there...


If this vehicle came prewired, and all you had to do was plug in the fog lamps, then 50A fuse 7 in the power distribution center would be hot at all times, applying power to 15A fuse 24 and the fog lamp relay. Setting the left multifunction switch to FOG causes the body control module to close the fog lamp relay and turn on the fog lamps. It is possible your Jeep came prewired but without the fuses and relay so a dealer could install them to make your fog lamps work. You can check whether the fuses are in the box and OK and whether the fog lamp is installed or just an empty socket. Once everything has been checked and any missing parts installed, your fog lights should work.

Sep 18, 2012 | Cars & Trucks

1 Answer

I purchased a used 2008 Jeep Patriot and it didn't come with fog lights. I have purchased OEM fog lights but I am having a hard time finding the connector plug to with them. Suggestion?


I have not run into this problem before. Usually, people either purchase the vehicle equipped with fog lamps from the factory or they add aftermarket fog lamps to the vehicle after purchase. In your case, you are trying to connect factory lamps that were not there from the factory? I'm not sure that you will find the connectors you are looking for. I do know for certain that the factory fog lamps are computer-controlled and that if the vehicle was not equipped with them from the factory, then the computer will not be programmed to make them work. If the wiring and connectors are there at all, they will be coming from the Totally Integrated Power Module (TIPM) located on the left fender. The factory wires are WHITE/YELLOW for the left fog lamp and WHITE/ORANGE for the right fog lamp. What about control switches,wire, etc. Did you purchase all of that as well?

Apr 24, 2011 | Jeep Patriot Cars & Trucks

1 Answer

How to change Ford Explorer fog light


p, li { white-space: pre-wrap; }

Open the hood and remove the electrical plug from the back of the fog light ballast below the headlight assembly.



Turn the fog lamp counterclockwise to unlock it from the fog light housing.



Insert the new fog lamp. Align the notches on the fog lamp housing with the tabs on the new bulb and turn the bulb clockwise to lock it into the housing.



Reconnect the fog lamp electrical plug.

Sep 13, 2010 | 1999 Ford Explorer

1 Answer

How to replace fog light bulb on an '03 Jeep


There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Feb 11, 2010 | 2003 Jeep Wrangler

1 Answer

Where is the front fog lamps swith on probe 1994 2.0


If you have them it would be on the console near your regular light switch, you may not have fog lamps they may just be standard bulbs

Dec 10, 2009 | 1994 Ford Probe

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

Installing after market fog lights


look where they mount the lights connectors are probably right there

Nov 01, 2008 | 1999 Jeep Wrangler

1 Answer

Front Fog Lamps


My guess is you have a corroded wire (that has shorted out the connection); known problem for this vehicle.

Sep 21, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...