Question about 1989 GMC Sierra

2 Answers

1989 GMC Sierra truck doors loose

1989 GMC Sierra truck doors and window handles are really loose how do i take the door panels off
thank you Nana2002

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 56 Answers

Hey there.You can purchase a door pin and bushing repair kit to tighten up the hinge area,requires removing the door to replace.If the hinge area is worn to badly,the brass bushings willnot last.Also your window crank handle is held on by a C-clip behind the handle in between the plastic shim and the handle which requires a special tool to remove or a small screwdriver to get the clip off.It is hard to see.The shaft that the handle is on are known to wear also and if thats the case you will need to have the window regulator replaced.Hope this helps.John.

Posted on Mar 10, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Rear axles is froze up

Posted on Sep 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the right side power window switch


You need to take off door pull. then unsnap door panel unscrew lock knob. Then slowly raise door panel unhooking it from handle that will still be sticking through. As soon as you have it unhooked from handle you should be able to tip it away far enough to get to switch on inside of panel. There should be harness clip to unplug from switch then unclip the switch. Not to hard just time consuming. Good luck

Apr 14, 2012 | 1989 GMC Sierra

1 Answer

Removing plastic door panel on a 2003 gmc sierra sl 2500hd 4x4 completed so far, -removed upper triangle piece opposite of door mirrior -removed door handle trim surround -removed 7mm screw under armrest...


what are you wanting to know?? the door is panel is still held on with clips, if your wandering why it still wont come off... start from the bottom corner of the door and work your way around. you will know when all of the clips are pulled lose, then just lift the panel up off of the door.

Dec 04, 2010 | 2003 GMC Sierra 2500HD

1 Answer

How do you remove the door panels from a 2001 GMC Sierra pick up


On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect any other wiring that may be attached to the door.

Nov 02, 2009 | 2001 GMC Sierra 1500HD

1 Answer

Inside door handle is loose and will not open door on my 1998 gmc sierra


take door panel off and make sure the steel rods are still on tight

Oct 15, 2009 | 2000 GMC New Sierra 1500

1 Answer

How do you install an inside door handle on a 1997 GMC Sierra?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can put the new handle in and reconnect everything

Sep 24, 2009 | 1997 GMC Sierra

1 Answer

Drivers Side Door Handle


You need to take inside door panel off This just clips on but there are screws in armrest and inside door handle look for any other small square covers that may hide screws Lift panel up Make sure window is up Disconnect wiring from panel and you can now get at door handle linkage and bolts

Jul 10, 2009 | 1989 GMC S-15 Jimmy

1 Answer

Is it hard to replace a broken door handle on the outside driver side door of a 2004 gmc sierra extra cab with power windows and door locks?


its tricky but not hard. remove the door panel and put the window up, look in with a light and it will be obvious what to do......

Jul 07, 2009 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

Replacing door handle driver side, exterior. How to release the lock set and put it on the new one?


u r asking 2 different things if u are working on a gm pick up as they r seperate items... door handle is bolted in, lock uses a clip... remove door panel!

Jan 11, 2009 | 1989 GMC Sierra

2 Answers

Replace glass, drivers door on 1997 GMC 1/2 ton Truck ,2wd, Power windows


The door panel is held onto the door with clips but first you need to remove the screws from the grab handle on the door panel. then pop the bezel off around the inside door handle. very carefully!!! then using a clip tool pry off the peice that covers the rear view mirror nuts and pry gently all the way around the door panel until its loose then lift it up slightly to unseat the window channel strip off the door, then unhook your wires. As for the window roll it up, tape it to the door then line up the 2 10mm bolts that clamp it to the regulator with the provided holes in the door, loosen 'em up roll the regulator down and remove the window. Have fun guys!!!

Oct 28, 2008 | 1997 GMC Sierra

1 Answer

Door panel removal


remove the door lock slide and will be a 7mm screw behind it and one under grab handle. also pop off the bezel around door handle. door panel will lift up and come off then you can get to window switch wires. look at the screws holding the window regulator sometimes the bottom screws come loose and cause rattle

Sep 03, 2008 | 2005 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...