Question about Ford Freestyle

1 Answer

When puting foot on clutch pedal it goeas to the floor pedal soft

Posted by on

  • 007_foster Mar 10, 2009

    how would you adjust clutch is hydrolic

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 259 Answers

I would guess it needs the clutch adjusting

Posted on Mar 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch goes all the way to the floor I have a standard Camaro 96 3.8


clutch pedals are suposed to go all the way to the floor , you sure you dont mean brake pedal (cus thats bad ! ) clutches should travel all the way to floor and release the "grab" of the engine about 2/3 down , this way they are more smoothly allowing shifting thru the gears and not jerking as you shift thru the gears , if clutch pedal does not start to "grab" the engines power by 2/3 off the floor and fully "grab"its power all the way up(slipping) ,and you have a hydraulic clutch (96's do) then the clutch disk may require replacement or there is a oil leak in the clutch/master/slave cylinder , look for small oil leaks from under car in area of foot pedals
clutches should be replaced as an assembly that includes , disk ,pressure plate, throwout bearing , with engine side clutch plate magnafluxed for heat cracks and any hydraulic oil leaks replaced or repaired

Mar 12, 2015 | 1996 Chevrolet Camaro

2 Answers

Clutch pedel adjustment


Try cleaning the throttle body, and the air control valve

Jun 05, 2014 | 2011 Hyundai i30 1.6

1 Answer

How to bleed a clutch


Get a friend to help. Press clutch down to floor and hold, have your friend loosen the line at the slave cylinder, or clutch actuator under the car enough that fluid squirts out. Have him tighten the line back up. Release the clutch and press back to the floor again. Have your friend repeat the process as before. (loosen to let fluid squirt out, then tighten back up) Release the pedal. Repeat this process untill there are no air pockets left in the line. NOTE: if your clutch pedal fails to return to the top, simply pop it back up with your hand/foot, wait a few seconds, then depress to floor again for another bleeding.

Nov 19, 2013 | 2001 Ford Focus

1 Answer

1996 nissan maxima clutch squeals pedal stuck to floor


Sound like you're going to need a whole new clutch assembly, but if the fluid level was dry you may have sucked air into the system which means that the clutch will have to be bled at the slave cylinder, just like you would brakes. The squealing sound is coming from the throw out bearing, usually when the do that it means that the bearing is frozen and cannot spin. Either way it looks like you'll be dropping the transmission to work on the clutch.

Jan 30, 2013 | 1996 Nissan Maxima

1 Answer

My clutch is broken there is no traction at all and it is stuck to the floor. I can raise the clutch with my foot but cannot change gear when the car is running. Its an 01 VW Golf, is there a cable in this...


The Golf has a hydraulic type clutch, it works off a master cylinder and uses a slave cylinder to engage and disengage. It has a hydraulic line, hose and tubing. Have you checked the fluid level in the master cylinder? Are there any leaks under your car? Often the seals go out on the slave cylinder and the fluid bypasses not allowing any pressure to build, resulting in a soft pedal that goes to the floor. Fill the master cylinder with approved fluid and "pump" the pedal by hand, you should start feeling some pressure build. Then check for leaks. if that is not the problem, you will need to troubleshoot the clutch for pressure plate problems or possible faulty master cylinder. Good luck, i hope this helps.

Jul 12, 2011 | 2001 Volkswagen Golf

2 Answers

I was parked on the side of the road in my ford ranger ute for about 3 to 4 minutes with the clutch pedal to the floor i was on the phone and then i could smell the clutch burning. I took my foot off the...


The clutch might be a hydraulic system. When it's leaking oil the pedal sticks to the floor and has to be pulled back manually. Because it's designed to be fail safe, it still works but only for some time till all the oil has leaked out.

The burning smell might be clutch oil dripping on the exhaust - meaning the seal on the clutch servo is leaking oil.

There are repairkits for clutch servo's - usually it's suggested to replace the cylinder seal on the clutch pedal also.

Jul 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

How do I determine if my clutch pedal ignition lock switch is bad on a 1996 Hyundai Accent?


YOUR CLUTCH START SWITCH.ENGINE SHOULD NOT START WHEN CLUTCH PEDAL RELEASED. YOUR ENGINE SHOULD START WHEN YOUR FOOT DEPRESSED CLUTCH PEDAL TO FLOOR..

Feb 23, 2011 | 1996 Hyundai Accent

1 Answer

You said it the slave cylinder was leaking to replace it how can i tell if its bad if its not leaking


usually when you have a bad clutch slave cylinder you know it right away because since it is a hydraulic part, once a seal inside the slave cylinder gets bad, it will start leaking fluid, at the same time, because the seal is not sealing properly, it will allow air inside the system causing your clutch pedal to feel soft and spongy.
When a clutch pedal feels that way, its an indication of air in the system and when this happens it makes it hard to operate the clutch properly because it engages even with your foot almost all the way to the floor. at times you may not even be able to place your car or truck in gear due to this problem.
A bad clutch master cylinder will have similar symptoms, make sure that you look closely at each one of these items to determine which one is the problem (the one malfunctioning will be the one leaking fluid)
One check you can do on the master cylinder is to depress the clutch pedal while someone watches the brake fluid reservoir level. if the level rises while the clutch pedal is being depressed than the clutch master cylinder is bad and should be rebuilt or replaced.

Jan 07, 2011 | Ford Explorer Cars & Trucks

2 Answers

Clutch pedal sticks to the floor; the brake reservoir was low


I believe your pressure plate is broken and at a minimum will have to be replaced along with the clutch disk.

Jul 04, 2010 | 2006 Ford Fusion

3 Answers

Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L


my rodeo had the same problem i corrected it by bleeding the slave cylinder. and is located on the driver side on the gearbox you will find it if you follow the line from the master cylinder down to the gearbox and if that helps but happens again it might have to be replaced.

Aug 01, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...