Question about 2000 Chevrolet Silverado

1 Answer

Brake lights Brake light on back of cab works but the brake lights on the bed don't work. The bulbs arent burned out. Can't find a fuse blown. any ideas???

Posted by on

  • bass1212 Mar 18, 2009

    I dont seem to be getting power to the bulbs when brake is applied. Checked the grounds. still lost

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 856 Answers

Be sure you are getting power to the bulbs. If so, make sure you have a good ground. Most systems send power to the bulb and then take a wire from the bulb to ground.

Good Luck and hope this helps.

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine starts but does not go into gear brake light , abs light , engine lite on Radio, ac/heater, clock, cig lighter, door locks, brake lights, etc not working


Well, check if you have brake lights to start with? If you dont have brake lights, it is possibly a brake light switch under the brake pedal or a stop fuse blown. ( with brake switch malfunctioning, this could set ur check engine light and also ur brake and abs light. Check this and get back to me. By the sounds of the other accessories not working, check your 10 amp guage fuse which i am not quite sure, could be under the hood or in the cabin. keep me updated.

Dec 10, 2013 | 2012 Toyota Tundra Tundra Crew Cab Pickup...

1 Answer

Brake lights don't work


First thing to check is the simple things. Be sure the bulbs aren't burned out, then check to be sure the fuse isn't blown. Let me know if that helps.

Feb 08, 2013 | 1996 Volkswagen Passat

1 Answer

My brake lights arent working but my emergency flashers are. would that be a fuse or a wiring problem?


if the third brake light is working and the left and right brake lights are not than the most likely problem is the turn signal multifunction switch.

If the third brake light is also not working and the bulb is good than check the brake light switch located above the brake pedal under the dash. There should be power on one wire all the time. There should be another wire that powers up with the brake pedal depressed. If no wires power up with the pedal depressed than the switch is bad.

I can get you specific wire information if you need it. Just let me know.

Aug 31, 2011 | 2001 GMC Sonoma Extended Cab

1 Answer

Brake lights don't work. Bulbs, fuses and brake light switch all okay. Center brake light works and the running lighs work.


Filaments on actual bulbs might be burned out, pull the socket out from the back of the tailights and do a visual check on the bulbs, replace if needed...

Aug 23, 2011 | 1996 Mercury Mystique

1 Answer

No brake lights check fuses no blown fuses but the center brake light work


If the center high mount brake light comes on when brake pedal is depressed, and the rear brakes don`t come on, and the fuses are not blown, then I would replace the rear bulbs.

May 02, 2011 | 2009 Nissan Altima

2 Answers

All the running lights work minus the rear tail lights but the brake lights work and the bulbs look good


I have a f-250 super duty,2001, dash& running lights don,t work, found a 15 amp fuse blown in engine compartment. fuse,s keep blowing. please help.

Jan 16, 2010 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Brake lights not working in rear


did you check the bulbs?
other than that, retrace the wires and it must be grounding out, check for 12volt inside bulb connector

May 12, 2009 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

Rear brake lights


they are seperate fuses and also has trailer light relay for tow package models , look for trailer light relay fuse , with key on check them all while your there , if fuse is good , swap with another relay , if that will not work , check bulb housing for melted terminals , lastly have body control module ckecked

Jul 02, 2008 | 2005 Chevrolet Silverado

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...