Question about 1998 Chevrolet K1500

1 Answer

98 taheo transfer case shifting problem

Will not shift into 2 hi, when pushing the buttons tranfer case defaults to 4 low, and will not shift out. the only i can get it out of 4 low is to disconnect the battery....i do have a bad anti lock brake sensor in the rt front? have replace the shift motor and the module under the dash....help

Posted by on

  • purple_hazze Mar 10, 2009

    i have a snap-on scaner and there are on codes present

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,000 Answers

I would take the truck to your local Auto Zone or Advanced Auto Parts store and get a code scan. It will help narrow down the issue.
Let me know what the codes are and we can go from there.
Regards,

Posted on Mar 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Silverado 1500 push button 4 wheel drive issue Light will light showing it is in 4 wheel drive but it is not. Auto button seems to work though.


2 speed electric shift transfer case problems #1 jack up truck place on 4 jack stands. Start and select 4 high position in drive release brake ad watch front driveshaft does it turn "yes" problem is axle actuator on passenger side of differential not engaging axle shaft. "no" apply brakes bring to a stop engage low range does low range work "yes" internal transfer case problems "no" electric transfer case shifting motor failure.

Oct 26, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

Surburban won't shift into 2 wheel hi insteads ends up in 4 wheel low


if its manual shift then inspect the linkage, if its push button then the motor/servo on the transfer case could be the issue. or the switch. i had to chase a simular issue on my tahoe and it ended up being the motor on the transfer case that selects the gears

Mar 13, 2012 | 1999 Chevrolet Suburban

1 Answer

I have a 97 Chevy blazer with push button 4 wheel drive and it don't shift In to 4 low or 4 hi and the light should flash for 30 second then go back to 2 hi if it can't shift but when you push the button...


How about to the switch , is there battery power ? Fuse #15 FWD 10amp. I/P fuse panel . BCM - body control module light's the switch indicators 2hi, 4hi,4low . Check fuse #6 10amp I/P fuse panel .
DTC 002
The transfer case encoder motor is an assembly which houses four separate channels. These channels are used to indicate to the transfer case shift control module the present gear position of the transfer case or if the transfer case is in transition between gears. The encoder motor assembly consists of an electronically conductive inner ground ring in contact with a three legged wiper arm. Each leg's length is such that it makes contact with the conductive regions of the four channels. When any leg of the wiper arm is making contact with the conductive area of any channel, the encoder provides a path to ground to the inner ground ring.
During electronic shifting, the transfer case shift control module monitors the transfer case encoder circuit for the proper operating sequence. If at any time during a shift, the encoder changes from one position to any position other than the next possible position, an error counter in the transfer case shift control module increments by four. After the counter reaches 32, the transfer case shift control module set a DTC 2, a permanent "encoder fault," and reverts to a 2HI to 4LO or a 4LO to 2HI shift pattern only. To guard against a transient, random encoder fault due to vibration, dirt, electrical noise, etc., the fault counter reduces by one each time the transfer case shift control module detects a valid encoder value. The encoder must intermittently fail 25 percent of the time for the transfer case shift control module to consider it faulty and store DTC 2.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
This step measures the voltage between the transfer case encoder circuit channels P, A, B, and C to ground.
This step tests the suspect circuit(s) for an open, short to power, or short to ground.
This step tests the encoder signal ground circuit for an open or high resistance.
DTC 2 -- Encoder Fault Step
Action
Value(s)
Yes
No
Schematic Reference: Transfer Case Control Schematics
1
Important: Check the transfer case shift control module for DTCs. The transfer case shift control module is not a class 2 device. DTCs are displayed on the transfer case shift control switch. Use the following four steps to obtain DTCs.
Turn OFF the ignition for 10 seconds.
Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
Turn ON the ignition, with the engine OFF.
Observe the transfer case shift control switch select buttons for flashing codes.
Did you perform the Diagnostic System Check - Transfer Case?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check
2
Disconnect the connector at the encoder motor.
Turn ON the ignition, with the engine OFF.
Measure the voltage between the transfer case encoder circuit channels P, A, B, and C to ground.
Does the voltage measure near the specified value?
4.8-5.1 V
YES - Go to Step 4
NO --Go to Step 3
3
Test the suspect circuit for an open, short to power, or short to ground. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
YES - Go to Step 8
NO - Go to Step 7
4
Turn the ignition switch OFF.
Test the encoder signal ground circuit for an open or high resistance. Refer to General Electrical Diagnosis and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
YES - Go to Step 8
NO - Go to Step 5
5
With a DMM at the transfer case module connector probe the encoder sign ground pin and ensure a good ground path through the module.
Did the DMM indicate a good ground path?
--
YES - Go to Step 6
NO - Go to Step 7
6
Replace the transfer case encoder motor. Refer to Motor/Encoder Replacement .
YES - Did you complete the replacement?
--
NO - Go to Step 8
--
7
Replace the transfer case shift control module. Refer to Transfer Case Shift Control Module Replacement .
YES - Did you complete the replacement?
--
NO - Go to Step 8
--
8
Clear all DTCs from memory. Refer to Diagnostic Trouble Code (DTC) Clearing .
Operate the vehicle while pressing each of the buttons on the transfer case shift control switch.
Does the DTC reset?
--
YES - Go to Step 2
NO - System OK

Aug 29, 2017 | 1997 Chevrolet Blazer

2 Answers

I got a 98 chevy k1500 z71 push button 4x4 and i press it to get it in 4lo and it blinks and goes back to 2wd i replaced the front actuator still nothing


are you shifting when in transmission is in neutral? more than likely its the encoder motor on the transfer case. check all the fuses.

Dec 27, 2010 | 1997 Chevrolet K1500

1 Answer

My 1999 suburban also stuck in 4 wheel. when i push the button to go into 2 hi it flashes the acuator pulls in then goes back into 4 hi. it wont stay in 2 wheel drive. i have replaces the control on the...


Did you ever think of having it diagnosed by a qualified repair shop ? Thier are aspects associated with this system you have no clue about. That's the first thing every one goes for , changing the switch . It flashes because codes are stored .
DTC B0768 Service Indicator Circuit High
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0357 Park Switch Circuit High
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error
You need a professional scan tool to check for these codes an too view data parameters .
Transfer Case Shift Control Module
The transfer case shift control module uses the VIN information for calculations that are required for the different calibrations used based on axle ratio, transmission, tire size, and engine. The system does not know which calibration to use without this information.
The direct battery supply line (CKT 1640) provides the power to the module and motor circuitry.
Transfer Case Encoder Motor
The transfer case encoder motor consists of a permanent magnet (PM) DC motor and gear reduction assembly. It is located on the left hand side (drivers side) of the transfer case. When activated it turns the sector shaft of the transfer case (clockwise or counter clockwise) to shift the transfer case. The encoder motor is controlled with a pulse width modulated (PWM) circuit within the transfer case shift control module. This circuit consists of a driver on both the Motor A and Motor B circuits. The encoder motor is bi-directional to allow the motor to shift the transfer case from 2HI or 4HI to neutral and 4LO positions.
Transfer Case Encoder
Your best bet ,take it to a qualified repair shop .

Jul 18, 2017 | 1999 Chevrolet Suburban

2 Answers

1996 chevy blazer will not go into 4wd hi but it will go in to 4wd lo. when you push the 4 Hi button it just flashes and then does nothing.


The major components to this system are a shift control motor that is mounted to the transfer case, and a shift control module that is behind your center console. since the transfer case is still shifting into 4wd lo, the shift motor is still moving somewhat, so the most likely cause is the shift control module, but there isn't an easy way to troubleshoot between the two...

Nov 16, 2009 | 1996 Chevrolet Blazer

1 Answer

1988 ford ranger 4x4. Push button for on the fly


That would be the actulator on the transfer case. More than likely it needs replaced. Check for good connection at the plug on the tranfer case.

Nov 03, 2009 | 1988 Ford Ranger

1 Answer

I have a 96 f 150 4x4 with push button 4 wheel drive. when i push buttons no light come on and tranfer does not work.


Tap on the electric shift motor on the transfer case with a small hammer,just incase the bushings are bad in the motor.Then try resetting the shift module which is located inside behind the passenger side kick panel,its white with a little red led light on top,if that doesnt work then try replacing it.

Sep 11, 2009 | Ford F-150 Cars & Trucks

1 Answer

97 chevy k1500 wil not shift into 4 high, just 4 lo and 2 hi


The motor that drives the transfer case is not working it has to be replaced.

Nov 03, 2017 | Chevrolet Cars & Trucks

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...