Question about 1989 Chevrolet C/K 3500

1 Answer

Location oil pressure unit on 98 chevy 305

K 1500 4x4 pick- up

Posted by on

  • Jim Mankowski Mar 10, 2009

    THANKS FOR THE HELP

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 60,775 Answers

Rear of intake manifold, approx center. U will need a special oil sender socket to replace it

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pressure location


it sound like the oil pressure sending unit is bad Had a 91 chevy do the same thing

Apr 04, 2014 | GMC Envoy Cars & Trucks

1 Answer

Suburban oil pressure sending unit


FIRST you need to get an actual oil pressure tester to hook up directly to where the oil pressure bulb is and see what you get there...

Dec 18, 2013 | Cars & Trucks

1 Answer

Chevy 350 oil pressure sending unit


The Oil Pressure Switch is located:Under hood, center, rear engine area, driver side of distributor, mounted in block. Here's what it looks like.he oil pressure switch is mounted to the top rear of the engine.

  1. Remove the electrical connector from the switch.
  2. Remove the oil pressure switch.
  3. To install, reverse the removal procedures.

Jul 18, 2013 | Cars & Trucks

1 Answer

I can't find the oil pressure switch on my 1990 Chevy s10 pick up


It's by the oil filter ,screwed into block,here's what is looks like,click here.

Dec 06, 2012 | Cars & Trucks

1 Answer

I have a 1976 buick regal 350 engine and the oil light comes on when the engine gets hot and it is at an idle. when you give it gas the light goes out. could this be the oil sending unit and if so where is...


it might be the sending unit, is it a buick 350 or a chevy. 350? if a buick engine the sinding unit should be on the side of the timing cover if a chevy 350 next to the dist.

remove the oil sinding unit and install a manuel gauge and see just what the oil pressure is if below 10 psi at hot idle replace the bearings and oil pump in the engine. if this is a chevy 350 make sure you replace the camshaft bearings this is were we use to see the gratest oil pressure loss.

Aug 20, 2011 | Buick Regal Cars & Trucks

1 Answer

98 chevy 1500 starts and then shuts right off have replaced fuel pump and filter ,crank sensor,cam sensor ,oil sen. coil,ign.mod and PCM


On some chevys the oil pressure sending unit closes the circuit to continue the fuel pump to run after start. In the event of a wreck ,the car stops running thus no oil pressure thus turns off power to the fuel pump .A safety to help prevent fires. When you first start the car, the computer turns on the fuel pump for about 20 seconds just enough time to start and allow the oil pressure sending unit to close the circuit to allow it to continue running. when the car car has NO oil pressure or the sending unit fails ,it will start then shut down..as many times as you try to start. replace the oil pressure sending unit and secure a good conection. Dan

Feb 13, 2011 | 1998 Chevrolet C1500

1 Answer

Where is the fuel regulator 98 chevy V6 pick up


The fuel pressure regulator is located under the upper intake plenumn. (The black plastic cover that sits on top of the intake manifold)
After removing this upper intake, the regulator will be on the back side of the fuel injector inlet housing.
Good luck

Apr 01, 2010 | 1998 Chevrolet C1500

1 Answer

Where is oil pressure switch in chevy lumina van 1996?


To locate the oil pressure sending unit, locate the oil filter and look above it and to the right, above the starter. You will see a long round sensor, this is the oil pressure sending unit. It screws into the engine block and when you remove it you will get a dribble of oil.

Jan 23, 2010 | 1996 Chevrolet Lumina Mini

1 Answer

Location of oil pressure sender on '98 Linc. Navigator


the oil pressure sending unit is usally located in the same side the oil filter is and this is because the oil filter is connected to the oil pump so there should be one little single wire in that area

Jun 27, 2009 | 2003 Lincoln Navigator

1 Answer

Oil pressure sending unit


Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Mar 17, 2009 | 2003 GMC Sierra 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...