Question about 1994 Ford Taurus

1 Answer

Windshield wipers do not work on intermittent setting. The wipers work otherwise, but would like to have this operation also

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Bad wiper motor

Posted on Mar 09, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 22 Answers

SOURCE: 98 camry windshield wiper

You will have to change the swich that control the wiper blades cause sometimes they go bad

Posted on Dec 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

My front windshield wipers will only work on high. Any suggestions?


Search Results

    My windshield wipers only work on high speed...? ' Yahoo Answers

    https://answers.yahoo.com/question/index?qid...
    Nov 11, 2006 - My windshield wipers only work on high speed. ... If it's the compound switch on the lever on the steering wheel, it can be a bit complicated to ...

    Windshield wipers - CarGurus

    www.cargurus.com > Questions > Mercury > Grand Marquis

    CarGurusMay 19, 2015 - Windshield wipers - My wipers stopped last week and the next day they ... slow or intermitt and only work on high speed and the washer wiper doesn;twork ... The LCM does not effect the operation of the motor or switch it just ...

    Windshield Wipers only working at highest setting - Ford Flex Forum

    www.fordflex.net > ... > General Ford Flex Discussions
    Feb 16, 2011 - Windshield Wipers only working at highest setting ... rear wiper worksjust fine, just the front wipers only work at highest setting. ... the wipers sometimes grinds out the gears thus only working at high sppeds. If it is the motor or Transmission for the wipers, can I fix this myself and how much would it cost me.

    Common GM Wiper Problem - YouTube

    ? 3:23
    https://www.youtube.com/watch?v=kc6e2Tmar68
    Oct 25, 2010 - Uploaded by roadragecustoms
    The windshield wipers only worked occasionally. ... My 1998 dodge ram wipers only work on high will this help me? thanks.... Express van. you have to take out the motor and the transmission from under the front of the van..

Feb 09, 2016 | Cars & Trucks

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

Wipers dont work


This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper 1 relay


?€¢
Wiper 2 relay


?€¢
Wiper diode


?€¢
Windshield wiper motor


?€¢
Windshield washer pump


?€¢
Windshield washer nozzles


?€¢
Windshield washer solvent container


?€¢
Windshield wiper arm and blade assemblies


?€¢
Windshield wiper transmission


?€¢
WIPER/SW 10A fuse


?€¢
WIPER 25A fuse


Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

Dec 05, 2015 | Cars & Trucks

2 Answers

Wipers don't work in high speed and when intermittent wipers are set they stop in the middle of the windshield.


Yes that is likely a switch problem. Before you buy any parts have a shop confirm my guess.

Mar 21, 2014 | 1994 Ford Crown Victoria

1 Answer

98 camry windshield wiper


You will have to change the swich that control the wiper blades cause sometimes they go bad

Dec 12, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1994 Ford Taurus Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74192 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

fordexpert

Level 3 Expert

5414 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...