Question about 1997 GMC Yukon

1 Answer

Rear turn signal bulb on passenger side of 1997 GMC Yukon needs to be replaced, how do I do this.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 56 Answers

Open your rear door and on the inside jam where the light is remove the two screws.There either a philips or torx head.Rotate out a little and litely pull the other side tabs out of the notches in the quarter panel side.Once you remove the light you will see a circut board with two more screws.Your bulbs are on the inside of the circut board.If your new bulb doesnot work,you may need to replace the circut board,there known to burn out.Hope this helps.John.

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear passenger stoplight and turn signal won't operate even after replacing bulb, flasher switch


Check the wiring to the bulb. There may be a broke wire shorting out.

Feb 20, 2013 | 1997 Buick LeSabre

1 Answer

No brake lights or turn signal


Remove the rear light housings on the back of your GMC Yukon.
There should be several light bulb sockets located on the back side of each housing.
Grasp each of the sockets, and turn them counterclockwise, while pulling outward to access the bulb.
After removing each bulb socket, check to see if the filaments inside the bulbs are broken, indicating a shot bulb.
Also, you may check to see if the wiring harness attached to each bulb socket is not loose, or show any sign of corrosion, plus, check the condition of the wiring itself for cuts, abrasions, and missing insulation, which will need to be repaired.
Finally, if none the above solutions work, the culprit may be a faulty multifunction turn signal switch, which is usually round in appearance and located underneath the dash.

Jan 17, 2013 | 1996 GMC Yukon

1 Answer

All new right rear bulbs, all blink when blinker is on, what can i do to fix this?


YOU MAY HAVE AN INCORRECT BULB INSTALLED VERIFY BULB #"S IE: 6054 ETC....CONSULT OWNERS MANUAL

Sep 12, 2012 | 2007 GMC Yukon

1 Answer

Is there an adjustment for the stop light switch on a 99 GMC Yukon. I have replace it and my brake lights still do not work. Park lights work fine.


There is no adjustment. The park lights are on a different circuit than the brake lights.
Do you have a third brake light that works. Its also on a different circuit but works from the same switch. Do your turn signals work. They use the same filament as the brake lights.
Also, the brake light circuit goes through the multi function (turn signal) switch.

Since the brake lights and turn signal lights use the same filament in the bulbs, the brake light circuit will pass through the turn signal switch. When a turn signal is used it cancels out the brake light for that side.

Let me know if your third brake light and turn signals work in the rear.
Also, if youy have not already, check/change the bulbs. The type of sockets those lights are in also get burned so look at them well.

Oct 18, 2011 | 1999 GMC Yukon

1 Answer

99 yukon denali drivers side turn signal in rear tail light not working, i replaced bulb and still nothing, I looked at the connections and wires and found nothing, front turn signal blinks fast, passenger...


The circuit board needs to be replaced. Which is the board that the bulbs sit in. If you remove the turn signal bulb. You will notice the bulb socket will be slightly burnt inside. I had the same problem with my 99 Denali and replaced the circuit board for $35.00. Now everything is fine.

Feb 01, 2011 | 1999 GMC Yukon Denali

1 Answer

My drivers side mirror turn signal does not flash, when front and rear tail lights flash.


You need to replace the bulb, which you should be able to find at your local auto parts store.

Jan 06, 2011 | 2003 GMC Yukon Denali

1 Answer

How do I install a new rt rear turning signal light on a 1997 GMC Sierra 1500 short-bed offroad?


Lower tailgate remove two screws on side of light t15 torx or phillips remove light. middle bulb is signal.To remove bulb push release tang and turn left to remove. Good time to change all bulbs. Same on other side

Feb 05, 2010 | 1997 GMC Sierra

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

Where is the ignition coil on my 1997 Yukon V8 engine


Remove your air intake off the throttle body and it is bolted to the vavle cover on the passenger side of the engine toward the rear.

Aug 30, 2009 | 1997 GMC Yukon

2 Answers

2006 GMC Canyon turn signals


have someone turn on the turn signal then someone check to see if there is power at the bulb socket in the front and rear of vehicle. if there is not check the flasher, if thats not it then check the wiring. you should also call the dealer and ask it may be a common mistake in thier wiring harness.

Jun 12, 2009 | 2006 GMC Canyon

Not finding what you are looking for?
1997 GMC Yukon Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...