Question about 2005 Pontiac Aztek

1 Answer

Need the tourque setting on front hub bolt on pontiac aztek

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 55 Answers

50 ftlbs

Posted on Mar 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need know how get shift out streeling knuckle on 2004 Pontiac Aztek front wheel drive what all tools i need


2004 Aztek: replace the right front steering knuckle - JustAnswer

www.justanswer.com > Car Questions > Pontiac Problems
2004 Aztek: replace the right front steering knuckle - Answered by a verified Pontiac Mechanic.

How do i change a CV Joint on a pontiac aztek - JustAnswer

www.justanswer.com > Car Questions Disconnect the outer tie rod end from the steering knuckle; do NOT loosen the tie rod end jam nut. Refer to Rack and Pinion Outer Tie Rod End Replacement in ...

steering knuckle video for 2004 Pontiac Aztek Google Search

Jun 25, 2017 | Pontiac Cars & Trucks

1 Answer

Looking for video on 2001 aztek bcm replacment


What is a BCM? It is a Body Control Module, it is under the Dash, 2 bolts and the Electrical Connector. Remove and Replace.

EASY!!!

Apr 12, 2013 | 2001 Pontiac Aztek

1 Answer

Where is the abs plug on pontiac aztek


The sensors are made right into thee heel bearing hub assembly on this. The plug on the rear is right on the bearing assembly. The front you just follow the wire coming off of the hub. If you do have to replace this hub due to a sensor, don't get a cheap one to fix it. Those go out within about a year and then you just have a wheel bearing problem which is more dangerous than an abs issue.

Mar 08, 2013 | 2004 Pontiac Aztek

1 Answer

2001 Aztek rear brakes thunking noise.


rear sway bar link pins and bushings

Oct 18, 2012 | 2001 Pontiac Aztek

1 Answer

2002 pontiac aztek front wheel bearing hub torque


  • Tighten the wheel speed sensor bracket nut to 12 Nm (106 inch lbs.).

  • Tighten ball joint nut to 60 Nm (44 ft. lbs.).
  • Mar 26, 2011 | 2002 Pontiac Aztek

    1 Answer

    Front wheel bearing replacement. how big a job? are abs hub and non-abs hub interchangeable?


    technically ,,,, theres no abs hub or non abs hub.... All of the ABS components are up by the master cylinder... What you are seeing is a Speed sensor ... just unbolt brake caliper and remove the 3 or 4 bolts that hold on the hub assembly on ... and reverse order to put back on .... and as long as you dont loosen the brake line you wont have to bleed the brakes .... should only take a hour or two ...

    Nov 20, 2010 | 2003 Pontiac Aztek

    1 Answer

    Service vehicle soon


    all these lights are probably associated with the abs.. have the abs scanned at an autozone or another shop and probably will determine a front hub assembly (abs sensor ) is bad.

    Jul 05, 2009 | 2003 Pontiac Aztek

    1 Answer

    Rear Wheel Bearing Repair; 2005 pontiac aztek


    Remove the brake caliper
    Remove the disc, (rotor)
    Remove the 34mm nut on the axel shaft
    Remove the three (3) bolts from the back side
    You will need a wheel puller (three jaw will work well)
    Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
    Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

    May 01, 2009 | 2005 Pontiac Aztek

    1 Answer

    Pontiac Aztek front wheel hub replacement


    try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you and also try Schram auto and truck parts for only GM parts 1-800-292-1032 and also try junkyarddog.com

    Mar 12, 2009 | 2003 Pontiac Aztek

    Not finding what you are looking for?

    Open Questions:

    See all 2005 Pontiac Aztek Questions

    2005 Pontiac Aztek Logo

    Related Topics:

    41 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8743 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...