Question about 2006 Chevrolet Impala

Open Question

Setting the time clock in a 2006 Chev. Impala

Can't get the time to flash when pushing on the clock button. The time is displayed when the car is turned on. Even when the engine is turned off the time can be displayed when you push the clock button on the panel.

Posted by on

3 Suggested Answers

localwonder
  • 6784 Answers

SOURCE: 2006 Chev Impala turn signals not working on rear

Two issues here, you will need to replace the flasher. this will correct the erratic turn signals.

Concerning the brake light. Make sure the bulbs are in working condition and, check the wiring harness for faults as well. if the bulbs and wires arr OK, replace the brake light switch.

You can test for proper current by pulling the brake light bulbs out the socket and, use the copper prongs inside the brake light socket for testing. use a volt meter and, hit the brake pedal and, see if the meter registers a current. if not, replace the wiring harness.

Posted on Jun 04, 2009

  • 7 Answers

SOURCE: program a keyless remote on a 2006 impala

push relearn again then press and lock and unlock for about ten seconds till u hear beep

Posted on Jul 15, 2009

  • 36 Answers

SOURCE: gear shift stuck in park and can't push in the

this is a shot in the dark since could be many things, but check the brake light switch, you have to put on brake to shift from park, had this happen on a ford ranger once, the switch worked under light pressure as far as lights were concerned but required heavy pressure to shift

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change clock


From the owners manual for the 2012 Impala Section 1-14.
(I have included a link from Chevrolet's website to the full manual)

Setting the Clock

To set the time for the Radio with

CD (Base):

1. Press the H button until the hour

begins flashing on the display.

Press H a second time and the

minutes begin flashing on the

display.

2. To increase or decrease the

time, do one of the following

while the hours or minutes are

flashing:

. Turn the f knob.

. Press ¨ SEEK or © SEEK.

. Press\FWD orsREV.

3. Press the H button again until

the clock display stops flashing

to set the currently displayed

time, or wait five seconds until

the flashing stops and the

current time displayed is
automatically set.

http://www.chevrolet.com/content/dam/Chevrolet/northamerica/usa/nscwebsite/en/Home/Ownership/Manuals%20and%20Videos/02_pdf/2k12impala.pdf

Mar 13, 2015 | 2012 Chevrolet Impala

1 Answer

How to set the clock on a 2008 chevy cobalt


Setting the Clock (H-clock symbol, O-pwr symbol, f-music note symbol)
Without Date Display
AM/FM Base Radio with a Single CD Player
This type of radio has a
H
button for setting the time.
You can set the time by following these steps:
1. Turn the ignition key to ACC/ACCESSORY or
ON/RUN. Press the
O
knob, located in the
center of the radio, to turn the radio on.
2. Press the
H
button until the hour begins flashing
on the display. Press the button a second time and
the minute begins flashing on the display.
3. While either the hour or the minute numbers are
flashing, turn the
f
knob, located on the upper
right side of the radio, clockwise or counterclockwise
to increase or decrease the time.
4. Press the
H
button again until the clock display
stops flashing to set the currently displayed time;
otherwise, the flashing stops after five seconds and
the current time displayed is automatically set.
To change the time default setting from 12 hour to
24 hour, press the
H
button and then the pushbutton
located under the forward arrow label. Once the
time 12H and 24H are displayed, press the pushbutton
located under the desired option to select the default.
Press the
H
button again to apply the selected default,
or let the screen time out

Dec 27, 2014 | 2008 Chevrolet Cobalt

1 Answer

How do i change the clock on a 06 Nissan Lafesta, manual is in japanes


Hope this helps
If you are talking about the clock on the DVD display then.....

Audio display model
1. Turn the audio unit on by pushing the "PWR"
button.
2. Push the "MENU" button until the display
indicates the clock adjustment mode.
If the "CLOCK OFF" is indicated on the display,
push the "TUNE" button to change the mode
to "CLOCK ON". Then push the "MENU" button
The time indicator will flash.
3. Push the "SEEK TRACK" button to adjust
the hour.
Push the "TUNE" button to adjust the
minute.
Pushing the , buttons will advance
and , buttons will turn back
the time.
4. Push the "MENU" button to finish the
adjustment.

May 24, 2014 | Cars & Trucks

1 Answer

How do you set clock on 2001 chevy impala


I'm going from memory on my 2002 Impala, but I recall that the key needs to be on, radio off.
Only the clock is displayed. Push one of the small buttons to change the Hours or Minutes.
Let me know if this was correct?

zeevert_42.jpg

Feb 11, 2011 | 2001 Chevrolet Impala

1 Answer

How do I set the clock in my 2006 Equinox... nothing in the manual


check page 3-39

Setting the Time
To set the hour, press the clock button. The clock
symbol will appear on the audio display and the hour
number will flash. Then turn the ADJ knob to increase or
to decrease the hour. To set the minutes, press the
clock button again. The minute numbers will flash.
Then turn the ADJ knob to increase or to decrease
the minutes. The time can be set with the ignition on
or off.
To synchronize the time with an FM station broadcasting
Radio Data System (RDS) information, press and
release the clock button to enter the clock set mode,
then press and hold the clock button for three seconds
until UPDATED appears on the display. If the time
is not available from the station, NO TIME UPDATE will
appear on the display.
RDS time is broadcast once a minute. After tuning to an
RDS broadcast station, it may take a few minutes for
the time to update.

Nov 30, 2010 | 2006 Chevrolet Equinox

1 Answer

How do i change the time?


Hello, here is the instructions for setting the clock

RDS Clock Time Broadcasters can choose to send clock time information in the RDS data. This information can be used to update the clock time on the radio. RDS clock time is broadcasted once a minute. To set the clock using RDS clock data perform the following:

• Press and hold the HR and MIN buttons together for two or more seconds to update the time.
• The display will show "UPDATED" after receiving the broadcasted time data. • If the broadcaster is not broadcasting the time data, the radio will display "NO UPDATE" and the time remains unchanged.

if this doesnt work, just simply push and hold the hr and minute buttons to set the time
• Press and hold the HR and MIN buttons together for two or more seconds to update the time. • The display will show "UPDATED" after receiving the broadcasted time data. • If the broadcaster is not broadcasting the time data, the radio will display "NO UPDATE" and the time remains unchanged.

Oct 23, 2010 | 2002 Chevrolet Impala

1 Answer

How do I reset the clock on a 2008 Impala, and 2008 Accord? I can't find the manuals


For the Impala:

AM/FM Base Radio with a Single CD Player
This type of radio has a H (clock) button for setting the
time. You can set the time by following these steps:
1. Press the H button until the hour begins flashing on
display. Press this button a second time and the
minutes begin flashing on display.
2. While either the hour or the minutes are flashing,
turn the f (tune) knob, located on the upper right
side of the radio, clockwise or counterclockwise
to increase or decrease the time. Instead of using
the tune knob, you can also press the SEEK arrows,
\FWD (forward), orsREV (reverse) buttons
to adjust the time.
3. Press the H button again until the clock display
stops flashing to set the currently displayed time;
otherwise, the flashing stops after five seconds and
the current time displayed is automatically set.
To change the time default setting from 12 hour
to 24 hour, press the H button and then the
pushbutton located under the forward arrow label.
Once the times 12H and 24H are displayed, press the
pushbutton located under the desired option to
select the default. Press the H button again to apply
the selected default, or let the screen time out.
With Date Display
Single CD (MP3) Player
This type of radio has a H (clock) button for setting the
time and date.
To set the time and date, follow these instructions:
1. Turn the radio on.
2. Press theHbutton and the HR, MIN, MM, DD,
YYYY (hour, minute, month, day, and year) displays.
3. Press the pushbutton located under any one of the
labels that you want to change. Every time the
pushbutton is pressed again, the time or the date if
selected, increases by one.
• Another way to increase the time or date, is to
press the right SEEK arrow or\FWD button.
• To decrease, press the left SEEK arrow or
sREV button. You can also turn the f (tune)
knob, located on the upper right side of the radio,
to adjust the selected setting.

The date does not automatically display. To see the
date press the H (clock) button while the radio is
on. The date with display times out after a few seconds
and goes back to the normal radio and time display.

Mar 15, 2010 | 2008 Chevrolet Impala

1 Answer

Setting clock after replacing battery 2006


simply turn on radio, then press and hold hr button till the hours are set then the min till it is set..

Sep 12, 2009 | 2006 Chevrolet Impala

1 Answer

1985.5 PORSCHE 944 digital clock (changing time)


There are three buttons, let's call them 1, 2, and 3, from left to right.


Clock
Time setting

A. 12 AM, PM or 24.00 h
With the clock in the time readout mode, keep
button (2) depressed for 4 seconds -12 AM, PM
or 24.00 flashing. After pushing button (1), either
a 12-hour (AM + PM) or a 24-hour setting
program can be selected. If you only want to
change the display mode, push button (3). The
clock then returns to its normal timekeeping
function.

B. Hours
Push button (2) a second time - hour display
flashes. Set hour by pushing button (1). After
pushing button (3)*, the clock returns to the time
readout mode with new hour setting.

C. Minutes
Push button (2) once more - minute display
flashes. Set minute by pushing button (1). Upon
pushing button (3)*, the clock is started -
accurate to within 1 second.

Stop watch function
The stop watch can only be set in motion if the
clock is in its normal timekeeping mode and not
during setting operations.
A. Push button (3) - 00:00 display appears;
B. Push button (1) - stop watch is on;
C. Push button (1) a second time - watch stops.
(Additional times can be added by pushing button
(1) again - stop watch keeps running. Push button
(1) once more to stop timing.)
D. Push button (2) - 00:00 display appears;
E. Push button (3) - normal timekeeping mode.

If button (3) is pushed during operation A and
B, the setting procedure must be restarted
(push button (2)). icon_biggrin.gif

Apr 17, 2009 | 1985 Porsche 944

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...