Question about 2000 Ford Expedition

1 Answer

Window off track on my expedition putting back on the holders sho

My window fell off the track/two little black holders. The holders one was loose one was tight should the holders be tight or loose

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

This black holders are part of glass and glass should be replaced

Posted on Mar 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What do i do if the window falls into the door and off track

pull door panel of and pull the window up ask some one to help u to hold it then raise up and down your track and slide window on ,then tighten up the bolts that holds it on track but make sur before you completly tighten the bolts to c if it properly set where the door can open and shut then tighten bolts on the rail and put the door panel back on : )

Jan 17, 2013 | 1997 Ford Expedition

1 Answer

How do i actually put the window back in track?

if it fell out or lost its track while you were operating it the window regulator has failed. remove the door panel and replace the regulator this is the whole assembly inside the door. if your replacing the regulator and you have slid the window out to do this you need to feed in in from the top its a little tricky but it will slide back in its track dont force it so you dont shatter it. the regulator keeps it all moving at the same time when the cables stretch over time they allow the window to sag one way or another and it fall out of its track and jambs. hope this helps

Jan 24, 2011 | 1997 Ford Expedition

1 Answer

I have a 1997 Dodge Ram. The window on the drivers side door fell off its track. I have the door panel, and the plastic off. How do I get to the window, and put the window back on its track?

I had the same problem on my 97 Ram. Take the door panel off, get some liquid nail, squirt just a little into the two clips that hold the glass. Then set the glass back into the clips and run the window up almost to the top so you can still get your fingers on top of the glass. Run it all the way back down again putting a little down pressure on it. Now run it all the way up, put the panel back on and let it sit for a few days before you roll it down again.
You have to run it up and down to make sure the clips are in the proper position, if yours is as loose as mine was it will slide around in the clips pretty easy.

Jan 07, 2011 | 1997 Dodge Ram 1500 Club Cab

2 Answers

Driver side window falls down it is a power window

Window has come off track,try to lube the track, reset the window in the track an use a apoxy glue let it sit for a few hours an it should b fine that's what I did to mine, that last snow storm we had my truck was covered,I was keying my truck warm up I went to open the window it was stuck, so I gave it a little hit an then it fell in the door an the snow came in lol, then I found out what to do I never had a prob again

Jan 02, 2010 | 2001 Ford Expedition

1 Answer

Window fell off track on a 1998 ford expedition how do i fix that

sounds like this could be a problem whithe the track or it came loose from the window regulator. very easy to tell what happend. take the door pannel off and just simply look inside. if it is the part that accualy monts to the window that is your regulator. if it looks like it was glued on to the window then you can go to any part store and pick up a tube of uerothane it comjes in a caulk tube apply this to the track on the regulator and put the window back in this will take about 24 hrs to fully cure. also do not close window all the way only about half way untill fully cured or at least 5 hours

Dec 30, 2009 | 1998 Ford Expedition

1 Answer

2003 ford expedition back drives window fell off the track

First check what caused the problem. If the window was hard to put up and down then clean the running rails either side move the window up and down with your hand to make sure it is moving freely then just glue the window back to the track with glue recomended for it

Aug 04, 2009 | 2003 Ford Expedition

1 Answer

My drivers side window fell off the track. how do i get it back on? or how do i take the door panel off to get it back on the track?

you will have to take the screws out of the panel or pull firmly to release the body fasteners once you have done this you will have access to the window you may have to move or cut the plastic away but keep it its there for a reason take the track loose by removing the screws place the window back in the track secure the track by putting the screws back and youre will need a little patience though if its your first time .

Jul 15, 2009 | 1990 Dodge Dynasty

1 Answer

Looks like window fell of the track rail

did you remove the screw in the arm rest if you did pull up on the panel from the front bottom

May 01, 2009 | 2000 Ford Expedition

1 Answer

1997 Ford expedition power window.

The only screws holding the door panel are the ones holding the armrest in place. You may find them under the armrest. Remove them. and then using either a trim stick or a small scraper or screw driver, feel around the edges of the door panel for the clips that are holding it in. If you use a screwdriver, use a pair of them as this will give you an even pull since you will put one on each side of the clip and then pull outward. Use a moderate tug to get them loose, not pulling too hard. I prefer to work from the bottom up to the top. Once you have that loose, you will need to get hold of the glass and walk it back into the track. Probably best to have a helper to hold onto it in case you find you need a tool that is not within reach.

Hope this helps.

Dec 16, 2008 | 1997 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

903 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5651 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides