Question about 2003 GMC Yukon Denali

1 Answer

Front wheel bearing

What is the recommended tourque for the axle nut on the front wheel bearing 2003 yukon denali AWD

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 450 Answers

156 ft lbs

Posted on Mar 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you remove the driver side cv axle from a 2005 Chevy asteo van AWD permenanlry


The CV axle stub (end with the axle nut on it) supports the wheel bearing, removing the axle then driving on it would cause the bearing to wear prematurely. I would not recommend this. The front differential is also sealed by the cv assembly, removing it would cause the diff fluid to leak out . CV shafts for this van run $50-80. I would replace if it is bad, instead.

May 04, 2014 | 2002 Chevrolet Astro

1 Answer

What are the torque settings on the front wheel hub bearing assembly for a 2003 gmc yukon denali xl?


155 Ft/Lb is the correct Torque

http://www.speedwayautoparts.com/Torque%20Specks.pdf

Mar 23, 2013 | 2006 GMC Yukon Denali

1 Answer

ABS enguaging on its own. Replaced both front wheel bearings. What would cause this? Had a recent MVI done and the Mechanic said the front Right wheel bearing need to replaced. He put a new on on and...


Not supposed to use air gun on axle nut

Torque Wrench -- as you did

Check Wheel Sensors -- one may be bad or more
likely the mechanic damaged it.

Use a Volt Meter --put on A/C unplug sensor &
put meter on wires and spin the wheels

Do all four & compare

Jul 24, 2011 | 2003 Cadillac Sts

1 Answer

I can't Desactived the four wheel drive where is the switch for the four wheel drive, is a GMC YUKON DENALI 2007


{: ) If your vehicle has an AWD (All-Wheel Drive) feature, engine power is sent to all 4 wheels all the time. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts ityself as needed for road conditions.

Jan 07, 2011 | 2007 GMC Yukon Denali

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

1 Answer

Left front axle seal


This is a fairly involved job. You will have to remove the brake assy, then seperate the ball joint and remove the axle assy. You will need a seal puller to remove the axle seal (At trans I assume) and a seal driver or something flat to install the seal. You will also need a 32mm socket ( if my memory is correct ) for the axle nut and a torx or hex socket for the brake caliper and a splitting fork for the balljoint. Be sure to tourque the axle nut to spec when reinstalling or you will be replacing a wheel bearing next. Hope this helps...Good Luck.

Feb 05, 2009 | 2003 Chevrolet Cavalier

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

2 Answers

2004 GMC Yukon Denali Awd humming sound in front of truck


The Denali's are really susceptible to front dif. wear and failure. Because it is AWD, the front dif is always working unlike a 4WD. GM, in order to lighten up the front end built the front dif in aluminum. If it was the same as the rear, it would be bullet proof, but much heavier. After about 80,000 miles it is common to have bearings failing. Remove the drain plug which happens to be magnetic. You may see more than just the normal fine filings. You will likely see larger chunks of metal some of which is not even magnetic but will drain out with the oil. You are likely looking at a $1500 rebuild. It will get much louder and run for a long time before it really goes south.

Nov 29, 2008 | 2005 GMC Yukon Denali

Not finding what you are looking for?
2003 GMC Yukon Denali Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...