Question about 1999 Dodge Durango

2 Answers

Brake problems i had a rattle so i pulled my tire off and my bolts that holds my calaper on have come outwhere can i go too order new bolts that work there way out

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,984 Answers

Go to Schuck's/Kragen/Chief's/Pep Boys.....prices range from $3.99 to $19.99.

Posted on Mar 09, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 463 Answers

Dealer.
Auto Zone
Advance Auto
Any NAPA
Federated Auto Parts Store.

etc., etc.

Posted on Mar 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front driver side tire blew out the lug nuts and the tire shout out. I need to replace the fender and studs. Could you tell me how to replace the fender?


The fender is bolted to the frame on the top, front, bottom and also at the rear, by the door. Just loosen all the bolts holding it on, pull it off and put the new one back on with all the same bolts. Also, the top bolts on the fender are hex type bolt heads.

Oct 25, 2010 | 1998 Jeep Grand Cherokee

1 Answer

How to change front brake pads on 2003 Chevy Suburban


Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket 93086g95.gif

  1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
  2. Raise and support the vehicle safely.
  3. Remove the wheel and tire assembly.
  4. Compress the brake piston back into its bore using a C-clamp.
  5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
  6. Remove the inboard and outboard pad.
  7. Remove and discard the anti-rattle clips.
To Install:
Caliper bracket sleeves 93086g97.gif

  1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
  2. Install new anti-rattle clips.
  3. Position the inboard and outboard pads into the support bracket
  4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
  6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
  7. Install the tire and wheel assembly. Lower the vehicle.
  8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
  9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.
Rear To Remove:
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
  5. Remove the brake pads from the caliper mounting bracket.
  6. Remove and discard the anti-rattle clips.
Rear brake caliper 93086g96.gif

To Install:
  1. Install new anti-rattle clips.
  2. Position the brake pads to the caliper mounting bracket.
  3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
  5. Install the wheel and tire assembly.
  6. Lower the vehicle.
  7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.
prev.gif next.gif

Jul 05, 2010 | 2004 Chevrolet Suburban

2 Answers

How difficult is it to cange the front rotors?


depending if you have the tools to do the job and pb blaster lock tite and white and dark grease for a beginer it has a rating of 7-8. if you work on cars and know what your doing, then its easy.. first thing is to remove the calapers then remove the calaper mounting bracket spray around the studs and bolts with pb blaster also around the hub and tap around the whole area around rotor dont hit the studs (with hammer) to break the rust buildup this should break rotor free then you may want to clean the rust off so that the rotors seat properly remove and clean new rotors with brake cleaner to get off the film off them (shipping rust retardent) and wipe. spray bolt holes to clear any rust left while removing old rotor and braket and dry. place a small ring of lock tite on bolts holding caliper brackets and let stand till harden or almost hard. replace new rotors install bracket/s and bolts (torq to ? 80foot lb) while replacing rotors replace brake pads, replacing just rotors will over heat new rotors in spots and warp rotors!!! make sure you pull the pins that retain the calipers to the bracket and add light coat of white grease to pins so calipers slides easy and evenly

Jan 21, 2010 | 2003 GMC Envoy

2 Answers

My car is making a rattling noise and leaking clear fluid


I am guessing the fluid is transmission fluid, the ratteling could be from the drive plate on the torque convertor, the vibration is damaging the front transmission seal, hence the leak. Trans has to be pulled, $4 seal replaced and possible the drive plate replaced from loose bolt damage, plate is about $40 to $80, about 5 hours labour, Hope this helps, Good luck

Nov 19, 2009 | 1997 Pontiac Sunfire

2 Answers

How to install front brake shoes on 1998 toyota camry


just take off tire take a clip out and pull out front shoe and take off roter then the back push in the cylender with a c clamp and revers the process of the calaper might come off using boltes then same process

Aug 29, 2009 | 1998 Toyota Camry

2 Answers

Remove and replace rotor on the front of an LX station wagon


Start by jacking the car up, place on jack stands for safwety, You will see the brake calaper which holds in the shoes, you will see two bolts which holds the brakes together, remove these bolts, then remove the pads. Remopve the bolt and pen holding the rotor on, take the rotor to a brake shop, see if it can be turned instead of having to purchase a new one. When replacing the brake pads you will have to use one of the pads to push the pressure plate back into the calaper to replace the pads. You may want to remove some of the brake fluid so it wont over flow when doing this.

Aug 07, 2009 | 1994 Honda Accord

1 Answer

How to change rear brake pads on audi a6 2006


Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.

May 20, 2009 | 2006 Audi A6

1 Answer

Changing brake pads


jack up car put on jack stands remove the ground cable from battery.take the wheel off the side your working on.take out the two bolts that hold the calaper on and bump it off with a hammer.depress the caliper with a 6in c clamp and put new pads in and put back together.go to other side same thing.

Feb 21, 2009 | 2002 Chevrolet Impala

2 Answers

2004 Toyota Camry Brakes


Raise the vehicle up and remove the rims & tires

Remove the brake pads, and then remove the calipers from the caliper retention brackets, do NOT remove the brake hoses from the calipers.

Remove the caliper retaining brackets from the hub assemblies (2 large bolts on backside of the bracket)

Tap the brake rotors off of the hubs, hit them from the back side of the rotor.

No big mysteries here, this is a very easy job.

Oct 21, 2008 | 2004 Toyota Camry

2 Answers

1998 Corolla Wheel Bolt


lugnuts and wheel studs
you will have to pull the barke drum off and knock the studs out and should be able to get new ones in and use a nut and spacer to pull the new studs tight

Aug 26, 2008 | 1998 Toyota Corolla

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

67757 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...