Question about 1999 GMC Yukon Denali

2 Answers

The needle on my gas gauge (99 denali) shakes when I turn on the engine. Anyone heard of that?

Posted by on

  • kirkharrell Apr 15, 2009

    Mine does the same thing about the same time that the engine choked when i hit the gas pedal. It choked out two weeks ago and will not start at all. Replaced the fuel filter, no change. Poured small amount of gas in intake and the engine turned over. I'm wondering if the fuel pump / gage are on the same circut and something has come loose.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My denali was doing the same thing it start one day and not the other,,,Change your whole distributor there is a sensor on the shaft which makes the timing work,, you cannot self adjust the timming on them engines

Posted on Jun 11, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Mine wouldn't start if the temp was below freezing outside. Dealer tracked problem to after market alarm system that was installed to the main wiring harness. He de-installed the alarm system and replaced the wiring harness. Like magic that and 4 other incideous little problems disappeared.

Posted on Apr 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the anti slosh module in a 1988 mercury grand Marquis ?


Anti slosh module? I've never heard of that. If there is such a thing, it must be on the fuel level sending unit in the tank. It is usually the sending unit at fault when the gas gauge stops working.

Here's how to check if the problem is the sending unit or the gauge in the cluster: you will need a helper to watch the gas gauge needle. Pull the electrical connector apart at the tank, find the gas gauge wire. The power wire for the fuel pump is pink and black, and the ground for it is a black wire, so the fuel sender wire should be a different color. When you figure out which wire is for the gas gauge, turn the key to on, and take a jumper wire and ground the gas gauge wire to the frame. Have a helper watch the gas gauge needle when you ground the wire: the needle should move perceptibly. If it does, the gauge in the cluster is good, and the problem is with the sending unit in the tank. If grounding the wire does not make the needle jump, the problem may be the gauge in the cluster. Be sure that you have made a good contact with ground with the jumper wire.
There is a small match box size voltage regulator on the back of the cluster. This sends low voltage (about 5 volts) through the gas gauge and on to the wire going to the tank. When you ground this wire, it should cause the gauge needle to go either to full or to empty, but you should see the needle move. Remember, key on, then ground the wire. Any movement of the needle means the gas gauge is probably good, and the problem is the sending unit in the tank.

Oct 24, 2014 | 1988 Mercury Grand Marquis

1 Answer

So my fuel pump has been making a high pitched noise for a while. Then one day, without warning, I tried to start the car but it wouldn't. It cranked but would not start. I turned the car on (not start)...


I looked at info for 3.1L vinM Buick regal. fuel pressure key on engine off, 40.5--47 psi. Can you check the vin? The fuel pressure specs I have for 3.8L engine are even higher than the 3.1L.
You will get a fuel pump prime, key on engine off. You need to make sure fuel pump runs with engine cranking.
My hearing is no good, I can't hear fuel pump with engine cranking.
Sometimes If fuel pump brushes are bad, the fuel pump may run intermittently. Sometimes you can bang on bottom of gas tank when trying to start and the fuel pump will take off running.

Apr 15, 2017 | Buick Regal Cars & Trucks

1 Answer

How can I get my gas gauge to work


There is a "balance" ball/gauge inside the gas tank.. Many times it gets stuck. If it is stuck, try to SHAKE THEentire car from the bumper while u r pumping gas... However, many times the "gauge ball" brakes and u have to drop the fuel tank:(

May 14, 2013 | Cars & Trucks

1 Answer

1970 Ford F100 Gas Gauge Not Working


It may be the sending unit in the tank that needs replacing. Here's how you can check: Turn the key on and disconnect the sender unit at the gas tank. Ground the sender unit's wire with a jumper wire from the truck's harness to ground. Watch the gauge. If the gauge on the dash is good, grounding the sender wire will cause the gauge needle to react and should move to full. This would indicate a new sending unit is required. If the gauge doesn't move when the sender unit is grounded, the gauge is bad and needs replacing. Pull the instrument cluster out to replace the gas gauge. Likely any old ford gas gauge might work-back then, there were not so many production changes.

Nov 14, 2012 | Ford Cars & Trucks

1 Answer

Erratic Gas Gauge


there is a big problem with these trucks fuel sending unit in the tank , going bad and needing replaced.

Jan 09, 2010 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

2007 GMC Envoy - Gas gauge showing empty and check engine light


This is a safety feature that the vehicle brings. You need to reset the E.C.U on dealership or it will keep doing it to you. It was probably caused by one single time that you did not closed the fuel cap correctly. Good luck

Dec 29, 2009 | 2007 GMC Envoy Denali

2 Answers

2004 GMC Yunkon Denali is misfiring


it could be alot of things...you could start by routine maintnence( new spark plugs, spark plug wires, air filter, oil change, the in line fuel filter) also take into consideration what kind of gas you are using...i know it sucks spending $100 a week in gas with your AWD 6.0 liter V-8...but if ur not running premium it could very well be your problem. I have also heard of the denali's having oxygen sensor issues...is it throwing a check engine code?

Dec 12, 2008 | 2003 GMC Yukon Denali

2 Answers

99 Oldsmobile Alero - Speedometer Problem - needle is stuck at 140mph


I replaced the radio with an aftermarket one and now my dash lights, power windows and my headllights have dont come on automataclly like they did before. my alarm on my remote dont work either, I think i did something to the alarm system, that is why they are not working.

Aug 18, 2008 | 1999 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...