Question about 1998 Ford Crown Victoria

1 Answer

1999 crown vic police int. cylinder numbers. - 1998 Ford Crown Victoria

Posted by on

  • Chuck Martin
    Chuck Martin May 11, 2010

    Passenger side front to rear 1 thru 4

    Drivers side front to rear 5 thur 8

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Pass Side from front to back 1 2 3 4
Drive side 5 6 7 8
all front to back

Posted on Jul 24, 2009

6 Suggested Answers

  • 178 Answers

SOURCE: 2003 ford crown vic hard steering

i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras

Posted on Sep 11, 2008

  • 69 Answers

SOURCE: P0304=misfire in cylinder 4. coil?

not coil coil it wouldnt fire at all it is either a plug or a wire replace the wire and plugs and that will fix it

Posted on Oct 06, 2008

  • 196 Answers

SOURCE: bad coil pack on crown vic

well if you have checked the spark plugs and they look good then its probly the coil If the plugs have never been replaced i would start with a tune up and see if this fixes the problem. If not there is no good way for you to test it you would need a computer to hook up to the car

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

bigc73542
  • 108 Answers

SOURCE: How are the cylinders numbered on a 1998 ford

Firing order is 1-3-7-2-6-5-4-8 Passenger side of engine starting at front and going back is 1-2-3-4 Driver's side starting at front going back is 5-6-7-8.

Posted on Jul 06, 2009

  • 66 Answers

SOURCE: 99 crown vic police interceptor steering wheel??

i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Posted on Jul 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bench bleed a master cylinder on a 96 crown vic


depends if it's on of off the car. much easier off; then you don't push alol that air into the system...

Sep 25, 2014 | 1996 Ford Crown Victoria

2 Answers

I have a 1999 Ford Crown Victoria Police Interceptor with a bad transmission. Will any transmission from a 1999 or 2000 Crown Vic. or Grand Marquis work as a replacement?


MOST INTERCEPTER CARS, MEAN THEY HAVE AN ADDED GEAR IN THE TRANSMISSION! WHAT YOU'LL BE DOING IS GOING TO A TRANSMISSION WITHOUT THAT EXTRA GEAR! TO ANSWER YOUR QUESTION: YES YOU CAN REPLACE IT WITH A REGULAR TRANSMISSION! YOU JUST WON'T BE ABLE TO CHASE BURGLARS! HAHA

Mar 04, 2011 | 1999 Ford Crown Victoria

1 Answer

Looking for rearend for ford crown victoria police interceptor


I have one. LBrown1806@juno.com. Selling my 1999 crown vic PI on Unocardealers.com zip code 55057. Please check it out.

Jul 16, 2010 | 1999 Ford Crown Victoria

1 Answer

2003 Crown Victoria: lost my only key to my 2003 police cron vic....


not to sound crazy ! do u own this car out rite! if so you can go to the dealer with the reg and they can cut u a key through the vin number! the key will cost 30 to 45 dollars ! its cheaper than a locksmith

May 05, 2010 | 2003 Ford Crown Victoria

1 Answer

99 crown vic police interceptor steering wheel??


i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Jul 07, 2009 | 1999 Ford Crown Victoria

3 Answers

Does the crown vic police intercepter take as much oil as the regular crown vic? (when changing the oil and filter)


I ~think~ the 1999 is the same as the 2000 (mine is a 2000 P71)

The 2000 CVPI (Crown Vic Police Interceptor) owners manual recommends the following:

Engine Oil - Motorcraft SAE 5W-30 Super Premium Motor Oil 5.0 quarts

Transmission Fluid - Motorcraft Mercon V ATF 13.9 quarts (fluids Mercon & Mercon V are NOT INTERCHANGEABLE, DO NOT MIX)

Fuel Tank - 19.0 gallons

Break Fluid - DOT 3


Rear Axle Lubricant - Motorcraft 80W-90 Premium Rear Axle Lubricant 3.75 pints (add 4 oz of Additive Friction Modifier C8AZ-19B546-A or equilavent meeting Ford Spec. EST-M2C118-A for complete refill of Traction-Lok Rear Axles)

Engine Data - 4.6L V8 Engine
Cubic Inches - 281
Required Fuel - 87 Octane
Firing Order - 1-3-7-2-6-5-4-8
Spark Plug Gap - 1.3-1.4 mm (0.052-0.056 inch)
Ignition System - Coil On Plug
Compression Ratio - 10.0:1

I hope this helps!

Jun 27, 2009 | 1999 Ford Crown Victoria

1 Answer

2003 Crown Vic Misfiring after acceleration


I just came up with that exact issue in my 2003 with 98K police crown vic. And the last time I had this issue in a 2001 police Crown vic it was the crank shaft position sensor. A $20 part and about 30 mins to put it in. located near the bottom of the engine. I had to un bolt the A/C compressor and push it out of the way a few inches to get to the sensor. If you have about 100K mile on it and its an idled heavy police car, this sensor should be changed out anyway. It can leave you on the road dead and some dealers have a hard time find out whats wrong as the OBD 2 does not see it as a problem when it goes bad or becomes touchy as I think mine is.

Jan 12, 2009 | 2007 Ford Crown Victoria LX Sedan

2 Answers

Engine light po 300 code


IS THIS A 99 CROWN VIC? IF SO IS IT MISFIRING? IF THIS IS THE CASE YOU MORE THAN LICKLY NEED PLUG WIRES.

Sep 06, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
1998 Ford Crown Victoria Logo

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...