a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
remove the door panel and inside the door at the bottom of the track you will find a bolt that adjusts the window track position
put the window down as far as possible and adjust the track back tight against the glass and tension up the nut
you take off the door panel by using a panel clip tool to pop the clips for the panel to come off also check for any screws holding the panel to the door by the inside door handle the bottoms of the panel once you get it off unplug the window door switches to move the panel out of the way but first lower the window track so you can see it remove the weather seal plastic and then when you can get to the track and the glass you'll see that there should be yellow circle clips that pop together to hold the glass with rivets I'm assuming the glass is broken and this might have come off and is in the bottom of the door use these for the new glass after drilling out the old rivets snap them together one on each side of the new glass and then put bolts and nuts on to tighten or use a rivet gun to the track reconnect the switches for door window power and raise the glass
The window track should have a bolt at the bottom so the track can be moved away from the window to allow enough room to slip it in between the tracks.Also the door skin can be unbolted to gain access from the outside of the door which may make it easier.
Try scrubbing the dirt out of the channels using a child's toothbrush. If that doesn't work, remove the inner door panel and check for window jumped out of track as a result of door slamming. Also be sure track mounting screw at bottom of tracks is tight and check operation with the panel off to be sure window raises and lowers smoothly without cocking in the tracks.
If you want to do this you need to remove the inner door panel( and maybe a weather barrier). be aware if you have any power options with switches on the door panel they must be disconnected before you attempt door panel removal.as soon as you remove the door panel(usually two or three screws and a dozen easily breakable plastic clips holding it in place) you will be able to see the window lift mechanism. if the window has not fallen completely off track you will be able to see how it is held by the "lift cradle" carefully without letting the window fall down into the door place the window back into its track"cradle" and loosely tighten the fasteners. and reconnect the window crank or window switch temporarily to slowly lift and lower the window while supporting it with your hand (to be sure it doesn't fall off its track while testing it) check if the window is tracking properly. if if seems to slide up and down appropriately and lands into the window seal appropriately then lower the window to a place where you can snug down the window retainers not too tight so as not to break the glass. and replace the door panel. after all switches or mechanisms are replaced test it again slowly to check for appropriate function and if you are satisfied pat yourself on the back for a job well done. i hope this helps
You will need a phillips screwdriver, non marring pry tool and a socket
set.The worst part is to pop off the
side view mirror cover on the door inside just above the door panel. Slide the
pry tool up and down until you hit the clip and gently push and pry the clip
out of each one of the receptacles.Unscrew the screws on the door trim and handles and lift the door panel
strait up then out with the window down. You should have access to the window
track and the mounting bolt. Loosen the lower part of the track and insert the
window in the track then tighten the mounting bolt. Test the window to make
sure the track is not bent or needs an adjustment.Reassemble the door if all looks good.
The window has likely come off the track. DO NOT roll the window up or down as it may scratch the glass inside the door. Their in a few screws and some body panel plugs to pull out. They make a special tool for this. I just give her a good yank, If they break don't worry they sell new ones at the dealer and most parts stores.
Yes. I have fixed my driver side window several times. The window went all the way down and came off the track, usually because the window automatically went all the way down. The first step was to take the interior side of the door off: (1) I unscrewed the screws around the door and pull the plastic screws out. (2) I disconnected the thin metal rod that connects the door handle to the door frame to be able to pull the interior part of the door away from the metal frame of the door. (3) I unscrewed the speaker to see where the window meets the rubber track. (4) I kept the electrical wires connected so that I could use the electric window button to lower and raise the window. (5) I lowered the window down below the rubber track and loosened the screw holding the rubber track to the door. (6) I manually adjusted the rubber track around the window glass and pressed the electric window button up slowly, making sure the glass stayed on the track. (7) I put everything back in place, screwed in the screws, etc. Be careful not to let the window go all the way down, because it seems to fall off the track at that point. Hope this helps!