Question about Pontiac Montana SV6

1 Answer

Rear brake rotors on a 2005 F150stx

How hard is it to change a rear Brake Rotor on a 2005 F150stx????

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 35 Answers

Shouldn't be too bad at all. If you have done brakes before. Remove tire, after securly jacking up vehicle and putting on some sort of solid object ex. axle stand. Then remove the caliper, should be two hex head slide pins or "bolts" persay. Then hang the caliper so you do not stretch or crack the brake line, use a piece of mechanics wire or something. Then the disk should pop off with a little persuasion. If not the parking brake is too tight. There is an inspection plug, remove that, loosen e-brake. Boom done. Congrats. Reassemble reverse.

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 gmc yukon denali rotor removel


Brake rotor and front or rear?

Okay, remove the wheel then remove the brake caliper and move to side do not allow to hang on the brake hose, use a hook to hang off spring or set aside. next remove the caliper bracket, two bolts at rear of bracket to remove it.
next you will use a hammer to remove the rotor.

NOTE: the way the brake rotor was designed was a bad one the hub in which the rotor slides over and the wheel studs slide into holes on the rotor is bad the hub diameter is almost the same size as the diameter of the seat of the rotor that slide over the hub and what happens is sometimes the rust build up on the rotor seat locks the brake rotor on the hub. i do not know if you are reusing the rotors or replacing them, no sure what job you are doing . the rotors to take off you will need to tap on the rear of them with a little force and turn, hit and turn. you will need to see if they break free or if hard beating and spraying into the rear of them is needed with wd40.
Alot of these rotors also have two threaded hole on the face of the rotor near the studs so that you can screw two bolts into holes to help pull them. use wire to tie caliper up and also use a c-clamp to push piston into calipe to remove caliper if needed, Do not remove brake hose, there is no need to open system, here is a picture of the rotor coming of the hub, also there may be clips on the stud holding rotor on remove them use cutters or pry off do not need to reuse , they are to help in holding the rotor on during asm, if you want you can buy them and reinstall them but never reuse them.12_25_2012_5_41_09_pm.png

Dec 25, 2012 | 2003 GMC Yukon XL

1 Answer

Is there a certain way to change rear brake rotors. They seem to be frozen and will not come off. I did not see a set screw in the rotors like some of the new models have.


ok i have been doing the for 22 yrs..heres the prob...inside the rear brake rotors r ur parking brake shoes..there is either a rust lip the built up on the inside of the rotor causing the parking brake shoes to grab the rust lip when u try to remove the rotor..if this is the case u will also need to repalce the rear parking shoes and the parking brake shoe holddown spring kit since it will probably break when u have to pry the rotor off....or u maybe able to de adjust the rear shoes by the self adjuster...look on the back side of the other side of the brake rotor an u should see a over slot just below the control arm...if it there use a brake spoon or straight slot screw driver to de adjust the rear park shoes.move it up or down ..one way will tighten them the other way will loosen them...if ur rotor doesnt move at all take off the rear caliper an hit the back side of the brake rotor to knock it off

Jul 16, 2011 | 1998 Ford Explorer

1 Answer

How to change the rear brakes and rotors..?


. Removal & Installation Front Front brake caliper & rotor removal/installation mitsubishi-09-00-7842.gif

Rear Rear brake caliper & rotor removal/installation mitsubishi-09-00-7843.gif

prev.gif next.gif

Dec 19, 2010 | 2005 Mitsubishi Galant

1 Answer

Having trouble removing rear disc brake rotor fron


This vehical has drum styal park brake shoes on the inside of the brake rotor so make sure the park brake isn't set and you can turn the rotor. If you can't turn the rotor you will have to look into this first if the park brake is set or sticking you won't get the rotor off if thats ok try spray with penting oil helps a little. I use a 4 or 5 lb sluge hammer and hit the rotor kinds close to the wheel studs about 5 times then hit the outer edge from the back side also works on the outerside. Don't be afread to hit hard I never broke one.

Jun 26, 2010 | 2005 Toyota Highlander

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

How do I remove rear rotor from 2005 hyundai tucson


What you have to do is first remove the screws that hold the rotor on to the hub, let off the hand brake shoes(they are located inside the rotors) there is a rubber plug on the face of thr rotor, take that off and loosen the hand brake adjuster! remove the brake caliper and caliper carrier and the rotor should come off! hope this helps

Sep 05, 2009 | 2005 Hyundai Tucson

2 Answers

How to remove rear brake rotors on a 2004 Santa Fe


THE REAR BRAKE ROTOR IS A LOOSE ROTOR AND SHOULD COME OFF EASILY. IF NOT, IT IS POSSIBLE THAT THE ROTOR IS HELD BY RUST ONTO THE HUB OR THE BRAKE SHOES IS STILL EMBEDDED INTO THE ROTOR. REMOVE THE HANDBRAKE CABLE TO ENSURE THAT THE BRAKESHOES COLLAPSE AND TRY TO LOSEN IT AGAIN. IF SEASED ONTO THE HUB BY RUST, KNOCK THE ROTOR WITH A COPPER HAMMER TO BRAKE THE RUST WITH A RUST REMOVER.

Jul 15, 2009 | 2004 Hyundai Santa Fe

1 Answer

Debree shields behind rear disc brake rotor rotted out.


Not hard to Replace. you will have to take the Caliper off of the Rotor and then Take the Rotor off, Repack the Bearings! And it is Right There!

Jan 18, 2009 | 2000 GMC New Sierra 1500

2 Answers

Back Rotors


do you have the parking brake applied if not you might have to back the ad juster off in order to get rotor off unless somethings come apart in behind the drum ive done lots of these and never had a problem hope this helps

Oct 22, 2008 | 2005 Dodge Caravan

1 Answer

Rear brake rotor removal


Should just pop right off. Hit it gently with rubber mallet, it might have rusted to the hub

Oct 03, 2008 | 2005 Kia Amanti

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...