Question about 1991 Honda Accord

1 Answer

I have bought Honda accord 91 and have no experience in its system. Its balance is not good. It is effected by any small stone in the rood . sometimes i found oils under it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

It might be blown gasket, or it might need to be aligned, go to any shop to have it checked usually 20 bucks or less to have it checked

Posted on Mar 11, 2009

  • thecrownking Mar 11, 2009

    or my suggestion to have the shop to check the brake caliper, i have the same model and year you have i have the same problem, but it is been fixed

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Harmonic balancer /water pump


most water pumps I believe have a weep hole that drips out coolant basically letting the person owning the car know that it is time to change the water pump. but then again have you checked to see if the water pump hoses are secure and aren't cracked?

Jul 06, 2013 | Honda Cars & Trucks

1 Answer

I don't know how to use my low beam light on my 91


The small dot is probably for park lights, the big dot for the headlights. For low beams, pull the switch lever towards you, just a light pull, you should hear a click.

May 10, 2012 | 1991 Honda Accord

2 Answers

I have a 91 Honda Accord EX the drivers side window will not go up or down all the other windows are working


Check the fuses, if they are all good then change the window motor on that one door!

Jan 10, 2011 | 1991 Honda Accord

1 Answer

What does the timming balancer belt do on a 91 accord lx 2.2


The Ballancer Belt runs the ballancer shaft which was installed in the motor from factory to help offset vibrations in the motor or counter ballance for the engine to run smoother

Nov 20, 2010 | 1991 Honda Accord

1 Answer

How do i replace the speedo senser on a 91 honda


I just had to do the same thing on my 92 accorcd I think yours is the same. It's on the passenger side of the transmission. Remove the large air tube from the air filter and push it aside. use a flashlight and look down on the transmission,you will see a small triangle shaped object that's it. It's not easy to get to there are two small bolts that hold it in place.You need a rachet and a long extension remove the plug and the bolts and pull it out. Then replace the new one. Ebay less than 20.00 auto parts 90.00. Good luck.

Jan 25, 2010 | 1991 Honda Accord

1 Answer

How tight should head tork bolts be on a 91 honda accord


on the 90-93 accord, tighten the bolts to 29 ft lbs on the first pass, 51 ft lbs on the second, and a final torque of 78 ft lbs, if you have a V-6 29 on the first and 56 on the second and final pass always start from the middle an work your way outward in balance 8,6,2,4,10 upper lower 9,3,1,5, 7 I hope this solves your issue, good luck!

Sep 30, 2009 | 1991 Honda Accord

1 Answer

My lifters are getting really loud on my 91 honda accord ex


All you need is to adjust the valve tappet clearance back to the original specification. It is a time consuming effort and require passion to do it. You need to remove the top engine cover, set timing belt to top dead centre then adjust intake & exhaust valve clearance one by one. Rotare the cranckshaft 180 degree and repeat the valve clearance,. I would suggest to leave it to the expert.

Jul 15, 2009 | 1991 Honda Accord

1 Answer

I have problem mi 91 honda accord ex coupe has vibration when im driving 55 & up im replaced l/f axle,control arm & balance the tires


Is there vibration in steering wheel? Check for bent wheel then check axle...again. Remans are not always good and new ones are just a bit more expensive. Also, check the output shaft bearing for excess play. Also try rotating tires to confirm it's not there.

May 10, 2009 | 1991 Honda Accord

2 Answers

Honda accord ex 92


Crankshaft pulley (harmonic balancer) removal- disconnect neg battery cable, remove belts, it would be a good idea to soak the bolt w/ penetrating oil overnight, there is a special 'crankshaft pulley holding tool' available to secure the pulley while removing and installing the bolt. Some parts stores loan tools for free if u purchase parts from them, I don't know if this is available, but it would be worth checking out. Attach holding tool and remove bolt securing pulley. Carefully remove pulley from crankshaft, Do NOT pry off. Remove key from crankshaft sprocket,
Install: install key on crankshaft sprocket, slide pulley on, apply clean oil to bolt threads but NOT to washer contact surfaces, secure crankshaft w/ holding tool, tighten to 159 ft lbs (91-93 Accord), install belts, re-attach neg cable.

Nov 11, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...