Question about 2003 Ford Escape

1 Answer

Left turn signal light out how do i replace it

Can not get to area to replace the blub detailes please

Posted by on

  • supertech199 Mar 09, 2009

    this is my left front turn signal

  • Chuck Martin
    Chuck Martin May 11, 2010

    front or rear?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 783 Answers

Again which turn signal bulb are you trying to replace on the left side,the front or the rear?

Posted on Mar 09, 2009

  • 1 more comment 
  • Chuck Martin
    Chuck Martin Mar 09, 2009

    I am assuming the front?



    Remove the wheel and tire.Position the inner fender well aside.






      1. Remove the bolts.


      1. Remove the pin-type retainers.


      1. Remove the screw.


      1. Position the inner fender well aside

  • Chuck Martin
    Chuck Martin Mar 09, 2009

    Then you can get to the bulb socket

  • Chuck Martin
    Chuck Martin Mar 09, 2009

    I guess it wasn't a front bulb?



    If it is a rear one open deck lid then remove the 2 screws on the inside lip and the outside snaps in place.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Passenger side turn signal flashes faster but dont work even at day runing light, comes on when head lights are on, replace bulb and socket because was melted but stilldoes the same


Turn Signal Lamps
The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side:
?€¢
The Rear Turn Lamp


?€¢
The Turn Signal Indicator


?€¢
The Sidemarker Lamp


?€¢
The Sideview Mirror (Pontiac Thunder only)

The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp.
The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass.
The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200.
When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off.
Which blub an socket did you replace ? check the other blub ? The switch and or the flasher module can cause this problem .
Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?

Which

Oct 11, 2015 | 2001 Pontiac Montana

1 Answer

Hyundai excel x3 Left turn signal doesn't work when reds are on, the reds flash when I use my left turn signal and also blows the fuse when left on for a little bit, I've replace the flasher relay, and...


sounds like a bad earth to me, any water ingress in the boot area? water in lamps? you should have at least one earthing strap from the wiring loom to the body of the car, find it/them undo them clean rust/paint from area reattach strap and cover with grease should solve it

Nov 12, 2013 | Cars & Trucks

2 Answers

I have 89 bronco 2 my brake lights turn signals both work my tail lights don't work have check fuse n blubs what might be the problem


The turn signals and brake lights use the same circuit and filament in the bulbs. The tail lights are on the other circuit which comes from the headlight switch.
Do you have power on the tail light fuse ?

Feb 25, 2013 | 1987 Ford Bronco II

1 Answer

My kawasaki 95 ZX9R no Tail Lights OR Brake lights


You are in the wrong section, this is for cars and trucks.

Jun 15, 2012 | Cars & Trucks

1 Answer

The left turn signal doesn't work, howerver rest does


check the blubs and you may have to replace the turn signal switch give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local Mercury dealership in the parts department and they be able to print you off the pictures and diagrams you will need wish you the best of luck Michigan Man.

Mar 22, 2010 | 2001 Mercury Sable

1 Answer

Left flasher dead, right on works


double check your bulbs again, if still good
check your flasher

G

May 09, 2009 | 2005 Jeep Wrangler

2 Answers

Front turn-signal bulb burned out.


It is a tight squeeze, but you can get your arm down past the headlight to the brake cooling duct and pull the brakeduct off the nose of the car back and to the side. Then you can reach through that hole and replace the turn signal blub

Jun 13, 2008 | 2001 Chevrolet Corvette

Not finding what you are looking for?
2003 Ford Escape Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...