Question about 1998 Dodge Neon

1 Answer

No spark on 2 and 4 coil both coils replased has same problem

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Dodge Master
  • 412 Answers

Try replacing the crank sensor..have seen this before

Posted on May 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replased head on 04 pt cruiser cranks but wont start


Make sure your cam and crank timing is correct, might have changed when you had the head off.

Feb 24, 2016 | 2004 Chrysler PT Cruiser

1 Answer

Cylinder misfire coil


These engines have 3 coils and are paired 1 and 4 2 and 5 3 and 6 with a spark noid run to see if the paired cylinder has no spark if so remove coil from module and test the power supply to coil and with a logic probe test the trigger side if blinking with no spark your coil is bad. not blinking replace module.

Apr 17, 2014 | 1994 Buick Park Avenue

2 Answers

Jeep 3.7 cylenders 2 & 4 not firing


3.7 V6, mileage?

most likely the HV wires bad.

then bad coil pack.

did you check spark directly at the coil pack?

i use 2 known good HV wires to do that and 2 good test spark plugs.

both plugs grounded to engine (shell)

that is how you test any wasted spark coil pack. 3 coil pack.

if that fails the FSM shows, unplugging it and check the coil resistances. if wrong the pack is bad,

keep in mind the res. can read ok and coil be bad ,due to internal insulation break down (internal shorts)

if thats ok. the resistance , make sure the wires are not (primary)

to the coil (the low voltage connnector)

if that is ok, its mostly likely a bad coil, (pray not bad PCM)

if tool-less? start with cheap parts , work to expensive. (guessing)





now wasted spark 101.

if one line opens , both spark plugs die. no spark

the wasted spark is wired in SERIES. ( like Christmas lights)

the magic cuts cost of 6 coil\'s.

so if the HV wires are say, cheap , carbon wire and open

you lose, both spark plugs. use MAG wire and end this issues.

get some nice NGK mag wire or Bosch Mag wires.

you can see i hate carbon wire. for good causes.

(carbon string wire)

mag wires is real wire that is coil spun and is inductive. it

has the correct impedance but is not a resistor its and inductor.

and lasts the longest , and worth every penny.

Mar 29, 2014 | 2006 Jeep Liberty

1 Answer

It has a miss to it i replase distributor coil ,spark plugs,wires, intake,


I think you need to take a compression test, you might have a bad valve.

Feb 27, 2011 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

How do you replace the spark plugs on a 1998 2.7 Intrepid?


Hi,
REMOVAL
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • Prior to removing the spark plug, spray compressed air around the coil area and spark plug.
  • Remove electrical connector from ignition coil.
On 3.5L engines, it is necessary to loosen the screws by alternating back and forth. Do not lose the spacers under the coil when loosening the screws.
  • Remove 2 fasteners from ignition coil.
  • Remove ignition coil assembly.
  • Remove the spark plug using a quality socket with a rubber or foam insert.
  • Inspect the spark plug condition.
INSTALLATION
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • To avoid cross threading, start the spark plug into the cylinder head by hand.
  • 3.5L engines tighten spark plugs to 28 N·m (20 ft. lbs.) torque, 2.7L engine tighten spark plugs to 17.6 N·m (13 ft. lbs.).
  • Install ignition coil assembly onto spark plug.
  • Install coil screws and tighten: 2.7L engine to 6.2 N·m (55 in. lbs.), 3.5L engines to 6.7 N·m (60 in. lbs.).
  • Connect the electrical connector.

Aug 27, 2010 | 1996 Dodge Intrepid

1 Answer

How do i plug in the spark plug coils? what order?


If it's the four cyl., the first coil pack bolts over the #2 spark plug. The #2 coil pack wire plugs into #3 spark plug. The number two coil pack bolts directly over the number four spark plug, and the #2 coil pack wire plugs into the #4 plug. The firing order is 1-4-2-3.

Jun 30, 2009 | 2000 Mazda Protege

2 Answers

1990 nissan sentra wont start


It seems you have a timing problem. Have the engine timed properly. If that does not work it could be a craked rotor or distributor cap. have all these checked.

Jul 30, 2008 | 1990 Nissan Sentra

Not finding what you are looking for?
1998 Dodge Neon Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...