Question about 1996 Jeep Grand Cherokee

1 Answer

Remote key will not lock doors

How do I fix the remote key? When I aim it at 1996jgc to lock the doors, the doors will not lock?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 254 Answers

There is a alarm mechanism inside the drivers door that has fallin off if you go the the passenger door and unlock it first the alarm will be disabled. what you would have to do is take the drivers side door panel off and look at the lock mechanism there should be a triangle shaft comeing out the back of it and there should be a black peice attached to a wire dangling in the door that needs to be glued back on but make sure to no glue the part of the peice that needs to rotate then test to see if it works before installing the door panel back on. 

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program this remote start . I just got this for a replacment one and It never came with the instuctions Please help me?


Instructions
    • 1 Climb into your Jeep Grand Cherokee with your keyless remote(s) in hand and your manual ignition key. Do not close the driver's door.
    • 2 Hit the "Lock" switch on your driver's side door and insert the key into the ignition.
    • 3 Turn the key to the "Run" position and aim the keyless remote at the steering wheel. Press and hold the "Lock" button for five seconds.
    • 4 Wait for the locks to respond by cycling then program each successive remote (up to four total) by holding the lock until the locks respond. Each remote must be programmed within 20 seconds of the last.
    • 5 Turn the key in the ignition back to the "Off" position then quickly back to the "Run" position within 20 seconds of programming your last remote.
    • 6 Turn the car off and remove the key from the ignition to complete the programming sequence.

hope this helps

Jan 19, 2015 | 2000 Jeep Grand Cherokee Limited

1 Answer

Hi, I have a Holden Astra TS city 98 model car and the remote on the key will open all the doors except the drivers door, so to lock all doors I have to put the key in the drivers door or use the remote &...


A plastic clip that holds the lock linkage is probably broke or worn. You need to pull of the inner door panel to see whats going on inside. Use the remote and see whats happening. It could be bent rod in door from someone using a slim jim to unlock it when they locked the keys in it at some point. Bend the rod and try the remote again untill it works properly.

Aug 31, 2014 | Cars & Trucks

1 Answer

Need instructions on how to reprogram my keyless entry remotes. Found some online but they didn't work


some of them you turn egnition on but not start open driver door. lock door lock by hand.aim remote at sensor and hold down lock button on remote till you hear it lock. within 15sec after you hear it lock turn key off and then back on but not start then turn key off and it should be good to go.,.... i hope. i got one from keyless ride.com took about 15sec. to program and only 50$ for what dealer wanted 250$ good luck hope this helps

Sep 15, 2011 | Buick Regal Cars & Trucks

1 Answer

Replaced batery in key fob and now there is no connection between fob and security system...I can lock and unlock doors with the key and I can start car ...fob doesn't work; does not lock or unlock...


reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

May 18, 2011 | 1999 Toyota Camry Solara

1 Answer

Where is the re-set button to program a remote door lock for my 2000 Subaru Forester?


Obtain all keys/remote controls. Remove driver's side kick panel/lower 'A' pillar trim. Connect central locking registration connectors (white) - black wire and black/blue wire Fig. 2 . Unlock the vehicle using the key. Program first key/remote control as follows: Press unlock button Fig. 1 [1], then lock button [2]. The door lock should lock and unlock in sequence confirming programming of first key/remote control. Repeat programming procedure for remaining key(s)/remote control(s). Once the last key/remote control is programmed disconnect central locking registration connectors. Check operation of all programmed keys/remote controls.

Sep 03, 2010 | 2000 Subaru Forester

1 Answer

I just bought a 1996 jeep grand cherokee larado, I locked the doo while inside with electric lock switch on door. I then opened the door with the handle. the alarm went off which I did not know it had. I...


lock with key,electric door lock button,or remote and alarm will set. to disarm you have to use the key or remote to open it.the reason it woulnt disarm from drivers door is either the door lock cylinder switch is broken or the wire to it in the rubber boot that connects the door and the body is broken.
the remotes are cheap and programing is easy,procedure in owners manuel something like lock drive door with elkect. lock switch with door open then push and hold unlock untill doors unlock then turn key off.you may have to fix that drive door lock cyl.switch first though mabee not dont know for sure

Mar 22, 2010 | 1996 Jeep Grand Cherokee

3 Answers

Yaris 2003 remote control lock problem


You need to reprogram the remote. Please se this website:
http://toyotaownersclub.com/forums/index.php?showtopic=85266

Oct 08, 2009 | 1998 Toyota Corolla

1 Answer

Mercedes mobliser problem


first check remote key battery possibly faulty battery, replace battery and check, when you operate remote aim it to the rear wive mirror not to the door lock, if not work after replace battery on key only option you have to drive your car to Mercedes workshop who have the right diagnose CPU for this particular model, if you plug any other diagnose CPU or tester you can't check this advance center locking system properly if you once fixed Mercedes diagnose tool in to the your car within short time period you can find what's wrong in your car it's easy fro experienced technician to do that, however before go to the workshop once again check all the fuses if any fuse blown replace it. is this information helped you?

Jun 20, 2009 | 1997 Mercedes-Benz C-Class

1 Answer

Automatic door locks will not work.


you need to take it to the dealer and have them check the bcm for codes.... also have them check to be sure you have the latest software in the bcm.. its possible that you just need a software update... there are several TSB's covering the concern you have..... it can be a very simple fix with software or even a stuck lock switch may need to be replaced... without the proper diagnostic codes being read from the bcm all that can be done is guessing..and that can be expensive...

Feb 02, 2009 | 2005 Chrysler Town & Country

1 Answer

Hardbody 2002


get into the truck and close and lock the door. place the key in and out of the ignition cylinder about six times(not too fast or slow) until you see the hazzard lights flash twice. then turn the key to the acc. position and then press the lock button on the remote(if lock doesn't work you can push another button on the remote). if the hazzard lights flash it is now programmed. then turn the key to off and pull it out and then unlock the door and open and close it. now test the remote.

Jul 21, 2008 | 1990 Nissan Hardbody King Cab

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...