Question about Buick Grand National

1 Answer

The control modaule and crank sencer has been replaced and their is no spark at the plug on a 1986 buick grandnational

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 168 Answers

First check the cam sensor too

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car wont start


In the circuit between the crank position sensor and the coil packs, is the ignition control module. It not only amplifies the crank position signal, but also does things like set the ignition advance curve as rpm goes up. It is expensive, but could be bad. First check to see it it is getting power, and it is not a fuse or a relay before trying that unit.

Jan 11, 2016 | 2000 Buick Park Avenue

1 Answer

Turns over but wont start


What kind of car???? if its a gm hop on this site and read it over... there is a common issue where the security fails on the car and I wont start.. it happened to my buick.did some research and now my car runs fine!

Sep 05, 2014 | Cars & Trucks

1 Answer

No spark wont fire 1986 buick regal


If the starter cranks very fast when you are trying to start to check for spark, it is a possiblity that you have a busted timing chain. This explains the rapid sound of you starter engaging, because the crankshaft is not being turned and the camshft is not either therefore no spark is made.

Apr 21, 2012 | 1986 Buick Regal

1 Answer

1999 Buick Lesabre Custom will turn over but won't start.


sounds like it could be your crank sencer or being a 99 does it have a distributor or a coil over plug ignistion system called a DIS [distributorless ignistion system] , if it has a distributor it could be cap and rotor that you need. best bet is to get a diognostic systems check but if no codes detected then you need to check all in line fuseable links for a dead short,a fried brain box ,or a bad pron in your ecm [electronic control module ]

Apr 04, 2012 | 1999 Buick LeSabre

1 Answer

1986 buick 3.0 engine stalls, no spark then after 10 min. there is spark


For spark plug problem, click the help links provided below: ---
Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

------------
How to Replace Spark Plugs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html

-------------
Car cranks, has spark but will not start?

http://howtobyme.blogspot.com/2011/12/car-crankshas-spark-but-will-not-start.html

------------------------
The spark plug firing order for car?

http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html

----------
How to gap spark plug ? http://technoanswers.blogspot.in/2012/02/how-to-gap-spark-plug-on-chevy-impala.html

-----------
Spark plug Replacing for?

http://technoanswers.blogspot.in/2012/02/spark-plug-replacing-for-chevy-impala.html

-----------
How to identify number one spark plug on the distributor cap?

http://schematicsdiagram.blogspot.com/2011/12/how-to-identify-number-one-spark-plug.html

---------
How does the spark plug wire go on the distributor cap?

http://schematicsdiagram.blogspot.com/2011/12/how-does-spark-plug-wires-go-on.html

---------
Spark plug Firing Order Diagram?

http://schematicsdiagram.blogspot.com/2011/12/2006-suzuki-forenza-spark-plug-firing.html

-----------

This will help.
Thanks.

Mar 03, 2012 | 1986 Buick LeSabre

1 Answer

How to replace cam possition sensor 3.8L vin3


it is most likely your crank sensor, it sends signals to engine module to give spark, make sure security system light is not on, the crank sensor sits on the main crank pulley, you may have to remove pulley to replace it, google instructions...

Jul 13, 2010 | 1986 Buick LeSabre

1 Answer

1986 Buick LeSabre with 3.8L V6 died while driving. Engine cranks but will not start. Checked fuel pump, injectors, lines, plugs and wires. Spark appeared possibly weak on the LeSabre compared to the same...


do you get fuel pump pressure, should be about 40 psi what about compression and spark on a saturn would be stronger due to many reasons one of which being different voltage of coils

Sep 30, 2009 | 1986 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...