Question about 2000 Mitsubishi Galant

1 Answer

Highbeams/turn signals not working!!!

I was replacing upper and lower radiator hoses and had to remove battery; when i put the battery back in, it "zpped", and now my highbeam headlights and turnsignals do not work(but the hazards and normal beams do work)...i have checked the fuses and they are all good..i switched the high-beam relay with low beam relay, and it works fine....anyone have any ideas?

Posted by on

  • 2 more comments 
  • toe mad Mar 13, 2009

    Ok, what wire would i look for and how would i know it's pinched? ive never come across the term "pinched wire" before....i know its not a ground bolt, i had no reason to remove any

  • toe mad Jul 25, 2009

    where can i find the HDLT casing?

  • Marc Podeszek May 11, 2010

    in the back of the hdlt casing check ground ground wires / They have a bolt that has a wire connected to it

  • Marc Podeszek May 11, 2010

    check for pinched wire or ground bolt that you may have taken out

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Look at the bulb sockets from the wiring when you push them in the wires cann ot be pinched between 2 things it will cause a short.

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and Replace my radiator


Open front hood "frunk" remove radiator cover plastic.

Remove upper radiator bracket supports.

Disconnect radiator fan wiring connectors.

Remove upper radiator fan bolts.

Jack up front of the car. Place jack stands and use ebrake and some kind of wedge to stop rear from rolling backwards for safety

Remove lower radiator fan bolts and lower fans down and place to the side.

Connect the factory clear tubes to the drain nossle by the lower passenger side of radiator if you still have them if not use a large enough collection pan so it doesnt splash much.

Open top release. Top of radiator driver side.

Place your bucket under the drain nossle and open that up. Let the coolant drain. When finished close both nossles.

If the radiator has not been replaced before or if it was put back the right way. Youre radiator hose clamps will be facing downward. Use some long needle mpse pliers to remove hose clamps and then remove the radiators hoses from radiator. Keep collection bucket under.

Once both sides of radiator hose are removed. Gently lift the radiator forward and upward to release the bottom of the radiator from where it is seated and then lower the radiator out the bottom.

Reverse to install and make sure to follow factory manual for bleeding coolant system after

Jul 05, 2014 | 1991 Toyota MR2

1 Answer

Replace raditor 2001 chrysler 300 M


1. Remove or disconnect the following:
  • Disconnect negative battery cable.
  • Drain cooling system.
  • Upper radiator hose .
  • Upper radiator closure panels.
  • Radiator fan assembly .
  • Radiator fan electrical connector.
2. Raise the vehicle

3. Remove or disconnect the following:
  • Lower splash shield.
  • Lower radiator hose.
  • Lower condenser mount bolts
4. Lower vehicle.
5.Remove or disconnect the following:
  • Upper radiator mounting brackets and bolts.
  • Upper condenser mounting bolts.
6. Separate condenser assembly from radiator.
7. Tilt radiator toward engine and remove radiator from vehicle.

Clean radiator fins are necessary for good heat transfer. The radiator and air conditioning fins should be cleaned when an accumulation of debris has occurred. With the engine cold, apply cold water and compressed air to the back (engine side) of the radiator to flush the radiator and/or A/C condenser of debris. The installation of the new radiator is the opposite of the removal. Please upvote if this was helpful. :)

May 04, 2011 | Chrysler 300M Cars & Trucks

1 Answer

Replacing the Radiator


YOU NEED TO DRAIN THE COOLANT SYSTEM. REMOVE THE AIR CLEANER ASSEMBLY.YOU NEED TO UNBOLT SWING AWAY THE ENGINE TORQUE STRUT MOUNTS FROM THE UPPER RADIATOR SUPPORT.LOOSEN THE THE THROUGH BOLTS IN THE STRUT MOUNTS FIRST TO AVOID DAMAGE TO THE RUBBER BUSHING.YOU NEED TO REMOVE COOLANT FANS AND REMOVE ELECTRICAL CONNECTOR FROM THE LOW COOLANT SENSOR IN THE RIGHT RADIATOR TANK.DISCONECT THE COOLER LINES FROM THE RADIATOR CAP ENDS LINES PREVENT FLUID LOST.USE DRIP PAN TO CATCH FLUID.BESURE TO TAG OR NUMBER TRANSMISSION COOLER LINES SO THEY CAN BE INSTALL IN THE ORINAL POSITION.REMOVE THE COOLANT OVERFLOW JUG HOSE FROM RADIATOR AND REMOVE THE UPPER AND LOWER RADIATOR HOSES THEN PUT EVERY THING BACK VISA VERSA.BESURE REPLACE ALL HOSES, TOP HOSE AND BOTTOM RADIATOR HOSE REPLACE THERMOSTAT AND RADIATOR PRESSURE CAP.IF YOU BEEN HAVING OVER HEATING PROBLEMS REPLACE THERMOSTAT ALSO.

Jan 19, 2011 | 1999 Chevrolet Lumina

1 Answer

How to change a radiator


1988–91 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 7: Cooling system components — 1988–91 engines 86833085.gif
1992–95 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 8: Cooling system components — 1992–95 engines 86833086.gif
prev.gif next.gif

Aug 27, 2010 | 1991 Honda Civic

2 Answers

How do I replace a radiator on a 2002 maxima


Nissan Car 350Z & Maxima 1999-06 Radiator - Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Coolant reservoir tank and bracket Upper mounting bracket Upper radiator hose Oil cooler lines, if equipped Lower radiator hose Cooling fan and condenser fan Fan motors and shields Radiator

To install:
  1. Install or connect the following:
    Radiator Fan motors and shields Cooling and condenser fans and torque the bolts to 44 inch lbs. (5 Nm) Lower radiator hose Oil cooler lines, if equipped Upper radiator hose Upper mounting bracket Coolant reservoir tank and bracket and torque the bolt to 44 inch lbs. (5 Nm) Negative battery cable
  2. Fill the cooling system to the proper level.
  3. Start the vehicle, check for leaks and repair if necessary.
WARNING Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Coolant reservoir tank and bracket Upper mounting bracket Upper radiator hose Oil cooler lines, if equipped Lower radiator hose Cooling fan and condenser fan Fan motors and shields Radiator
To install:
  1. Install or connect the following:
    Radiator Fan motors and shields Cooling and condenser fans and torque the bolts to 44 inch lbs. (5 Nm) Lower radiator hose Oil cooler lines, if equipped Upper radiator hose Upper mounting bracket Coolant reservoir tank and bracket and torque the bolt to 44 inch lbs. (5 Nm) Negative battery cable

  2. Fill the cooling system to the proper level.
  3. Start the vehicle, check for leaks and repair if necessary.
WARNING Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
240ef5f.jpg

Fig. Exploded view of radiator and components
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    CAUTION Do not damage or scratch the A/C condenser and radiator core while removing.
    CAUTION Because A/C condenser is onto the front-lower portion of radiator, moving to rear direction should be at minimum.
    Negative battery cable Engine cover Air duct and air cleaner case assembly Bracket mounting bolt for anchoring A/C piping Reservoir tank and bracket Upper and lower radiator hoses Radiator cooling fan assembly On A/T models, A/T fluid cooler hoses. Plug hoses to avoid leakage Cover, then two A/C condensing mounting bolts located in the upper part of the radiator Rotate two radiator upper mount brackets 90 degrees in the direction shown in the illustration and remove fce8147.jpg

    Fig. Removing A/C condensing mounting bolts

    d3c8f50.jpg

    Fig. Rotating radiator upper mount brackets 90 degrees

    edb9f67.jpg

    Fig. Removing radiator
  4. Remove the radiator by performing the following:
    CAUTION Lifting A/C condenser should be minimum to prevent a load to A/C piping.
    With lifting and pulling radiator in a rear direction, disassemble lower mount from radiator core support center. Lift A/C condenser up and remove radiator after disengaging the fitting as front-bottom surface After removing radiator, put A/C condenser on radiator core support center to prevent a load to A/C piping, and temporarily fix it with rope or similar means

To install:
  1. To install, reverse removal procedure.
  2. Check radiator cap for any leaks.
  3. Start and warm up engine. Check for engine coolant leaks and A/T fluid leaks.

Hope this help (remember comment and rated this).

May 12, 2010 | 2002 Nissan Maxima

1 Answer

How to remove and replace radiator on 1998 ford taurus


  1. Disconnect battery ground cable.
  2. Remove the battery.
  3. Remove clip retaining constant control relay module and position module aside.
  4. Remove battery tray.
  5. Remove radiator cap.
  6. Raise vehicle on hoist.
  7. Remove radiator splash shield.
  8. Drain engine cooling system.
  9. Remove radiator mounting bracket assembly.
  10. Remove lower radiator hose.
  11. Partially lower vehicle.
  12. Remove upper radiator hose.
  13. Remove radiator overflow hose.
  14. Remove upper A/C condenser core retaining bolts.
  15. Remove upper A/C transmission oil cooler tube clips.
  16. Remove upper transmission oil cooler tube (7C410) using 3-8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  17. Raise vehicle on hoist.
  18. Remove lower transmission oil cooler tube clips.
  19. Remove lower transmission oil cooler tube using 3/8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  20. Remove transmission oil cooler bracket and position transmission oil cooler aside.
  21. Remove lower A/C condenser core bolts and position A/C condenser core (19712) aside.
  22. Remove radiator support bracket.
  23. Remove radiator.

May 07, 2010 | 1998 Ford Taurus

1 Answer

How do i remove radiator fan from my 2004 pt cruiser?


Hope this helps!

Removal & Installation
NOTE The fan motor, fan, and the shroud are serviced as an assembly.



CAUTION Do not open the radiator draincock with the system hot and under pressure, because serious burns from coolant can occur.


  1. Disconnect negative cable from battery.
  2. Remove battery and battery tray.
  3. Drain cooling system below upper radiator hose level.
  4. Remove grille.
  5. Remove upper radiator closure panel and center brace.
  6. Disconnect upper radiator hose from radiator.
  7. For turbocharger equipped vehicles: Remove radiator inlet neck.
  8. Hoist vehicle.
  9. Disconnect radiator fan electrical connector (.
  10. Remove the two lower and left side radiator fan screws and.
  11. Lower vehicle and remove the remaining radiator fan attaching screws.

    WARNING Care should be taken not to damage the radiator cooling fins and tubes during fan removal.

  12. Remove radiator fan by lifting up from the engine compartment.

c83d6ac.gif
Radiator fan mounting points

To install:
  1. Install the radiator fan into position on the radiator.
  2. Hand-start all radiator fan fasteners.
  3. Tighten all radiator fan retaining screws to 55 inch lbs. (6 Nm).
  4. Connect the radiator fan electrical connector.
  5. Carefully lower the vehicle.
  6. For turbocharger equipped vehicles: Inspect radiator inlet neck O-ring. Replace if necessary. Install radiator inlet neck. Torque fasteners to 55 inch lbs. (6 Nm).
  7. Connect the upper radiator hose to radiator. Align hose and position clamp so it will not interfere with the engine or the hood.
  8. Install upper radiator closure panel and center brace.
  9. Install grille.
  10. Install battery tray and battery.
  11. Connect cables to battery.
  12. Fill cooling system.

Apr 18, 2010 | 2004 Chrysler PT Cruiser

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

2 Answers

How to replace a radiator in a chrysler concorde 1998 3.2


drain radiator.. remove upper and lower radiator hoses ,,remove transmission lines..remove bolts from cover on top of radiator.. lift out radiator.

Dec 06, 2008 | 1998 Chrysler Concorde

1 Answer

Replacing radiator 95 Jeep GC


No it is not difficult to replace a radiator it can be done with basic handtools I would not suggest a used radiator, if at all possible spend a little extra now and buy one with the best warranty (lifetime) available although with a new one you are looking at approx $250 plus coolant. Here is the proper procedure for replacment
Grand Cherokee
See Figures 9, 10 and 11
  1. Disconnect the negative battery cable.
  2. Open the radiator valve and drain the cooling system.
  3. Remove the fan and shroud assembly.
0900c152800a9917.jpgFig. 9: Radiator and condenser mounting
  1. If equipped, disconnect the automatic transmission cooling line quick-fit connections.
  2. Matchmark the upper radiator crossmember and adjust the crossmember to the left or right.
0900c152800a9918.jpgFig. 10: Radiator upper crossmember assembly
  1. Eight clips are used to retain a rubber seal to the body. Gently pry up the outboard clips (2 per side) until the rubber seal can be removed. Do not remove the seals entirely. Fold back the seal on both sides to access the grille opening reinforcement mounting bolts and remove the bolts.
  2. Remove the grille.
  3. Remove the upper brace bolt from each of the 2 radiator braces.
  4. Remove the crossmember-to-radiator mounting nuts.
  5. Working through the grille opening, remove the lower bracket bolt securing the lower part of the hood latch or hood latch cable from the crossmember.
  6. Lift the crossmember straight up and position it aside.
  7. If equipped with A/C, remove the 2 A/C condenser-to-radiator mounting bolts which also retain the side mounted rubber air seals.
  8. If not equipped with A/C, remove the bolts retaining the side mounted rubber air seals compressed between the radiator and crossmember.
Note the location of the air seals. To prevent overheating, they must be installed in their original position.
  1. Disconnect the coolant reservoir/overflow tank hose from the radiator.
  2. Disconnect the upper hose from the radiator.
  3. Carefully lift the radiator a slight amount and disconnect the lower hose from the radiator.
  4. Lift the radiator up and out of the engine compartment, take care not to scrape the fins or disturb the A/C condenser if equipped.
If equipped with an auxiliary automatic transmission oil cooler, use caution during radiator removal. The oil cooler lines are routed through a rubber air seal on the left side of the radiator. Do not cut or tear this seal.
To install:
0900c152800a9919.jpgFig. 11: Radiator alignment dowels
  1. Lower the radiator into the vehicle. Guide the alignment dowels into the hoses in the rubber air seals and then through the A/C support brackets, if equipped. Continue to guide the radiator through the rubber grommets located in the lower crossmember.
If equipped with A/C, the L-shaped brackets, located on the bottom of the condenser, must be positioned between the bottom of the rubber air seals and top of rubber grommets.
  1. Connect the lower radiator hose to the radiator.
  2. Connect the upper radiator hose to the radiator.
  3. If equipped with A/C, install the bolts condenser-to-radiator mounting bolts.
  4. If not equipped with A/C, install the rubber air seal retaining bolts.
  5. Connect the reservoir/overflow tank hose to the radiator.
  6. If the radiator-to-upper crossmember rubber insulators were removed, install them.
  7. Install the hood latch support bracket-to-lower frame crossmember bolt.
  8. Install the bolts securing the upper radiator crossmember to the body.
  9. Install the radiator-to-upper crossmember nuts.
  10. Install a bolt to each upper radiator brace.
  11. Install the grille.
  12. Position the rubber seal and push down on the clips until seated.
  13. If equipped, connect the transmission cooling lines.
  14. Install the fan shroud with the fan.
  15. Install the fan and shroud.
  16. Rotate the fan blades and ensure they do not interfere with the shroud and at least 1 inch (25mm) of clearance is allowed. Correct as necessary.
  17. Fill the cooling system.

Nov 24, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Mitsubishi Galant Logo

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...