Question about 2003 Hyundai Tiburon

1 Answer

LEFT TURN SIGNAL LTS STAYING ON AS WELL AS IND. ARROW IN INSTRUMENT PANEL AFTER CAR IS TURNED OFF. ONLY WAY TO GET OFF IS BY PULLING HAZARD FUSE

Posted by on

  • 1 more comment 
  • bec_stev Mar 10, 2009

    thanks for letting me know am going to try a used part hopei have no trouble doing it steve

  • Anonymous Apr 20, 2009

    Right signal front and rear stay on permanently as well as green turn arrow in guage cluster. Need new Body Control Module (BCM). I've also seen it described as a Electronic Chassis Control Unit.



    If I'm not mistaken, the part number (that I'm ordering used as I sit here) is 95410-2C100.

  • Anonymous May 02, 2009

    Its the BCN - and your right 1200 to fix it..... I love being an Huyandi owner, and my check engine light is stuck on too becuase of the BCM!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yep, happened to me as well. Same side and everything. Turns out they have to replace a component on the BCM by replacing the BCM itself. Runs about $1000 - $1200 at the dealer. Tough luck but there is a chance it is still covered under your warranty.

Posted on Mar 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My turn signals sometimes will quit working then I have to hit the hazard lights button leave it on and then turn my turn signals on then they work what causes this to happen


When the turn signals quit working pull up , down , front to back an back to front on the turn signal switch handle . Do they work when doing this ? Pontiac had bad switch . The power for the turn signals goes through the flasher / hazard module . Could be the switch or the module.
The HAZARD LPS fuse in the left hand instrument panel (LH IP) junction block supplies battery positive voltage to the flasher module, which is part of the hazard switch assembly. The TURN LPS fuse in the LH IP junction block supplies ignition positive voltage to the flasher module. The turn signal lamps may only be activated with the ignition switch in the ON position. When the turn signal switch is placed in either the left or right position, current flow is from the flasher module's output to the turn signal switch assembly. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators.

Mar 12, 2016 | 2001 Pontiac Grand Am GT

1 Answer

The hazard lights im my 2003 chevy trailblazer stay on. Even though there not turned to on position


The turn/hazard flasher module is probably bad .
Removal Procedure
  1. Remove the left closeout/insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side in Instrument Panel, Gages and Console.
    showgif.do?image=763321
  2. tif.gif
  3. Remove the flasher retaining bracket from the insulator panel.
  4. Disconnect the flasher from the electrical connector.
  5. Remove the flasher from the vehicle.
Turn Signal/Hazard Flasher Module
Behind the I/P near the headlamp switch

Dec 30, 2015 | Cars & Trucks

1 Answer

Where is turn signal flasher on 2001 olds aurora


Hazard and Turn Signal Flasher Replacement
Remove the left knee bolster. Refer to Knee Bolster Replacement in Instrument Panel, Gages and Console.
Remove the left IP endcap. Refer to Instrument Panel Outer Trim Cover Replacement
Gently pry outward on the rear edge of the IP outer trim cover until the retainers securing the outer trim cover to the IP retainer disengage from the retainer. Slide the IP outer trim cover rearward until the tabs on the front edge of the outer trim cover disengage from the IP retainer.
Remove the knee bolster compartment by pulling past the holding tab (1) and lifting up.
Unsnap the knee bolster by pulling down and rearward to remove from the vehicle
Remove the hazard and turn signal flasher module (1) from the I/P carrier. Disconnect the electrical connector.
>

Feb 12, 2015 | 2001 Oldsmobile Aurora

2 Answers

Where is flasher relay on 1995 Taurus?


An electronic combination turn signal and emergency warning flasher is attached to the lower left instrument panel reinforcement above the fuse panel.
The turn signal unit is located on the LH side of the instrument panel. The combination turn signal and hazard flasher can be removed by pressing the plastic retaining clip and pulling straight rearward. One phillips® head or regular screw has to be removed from the retaining bracket. It's square not round !

Oct 24, 2013 | 1995 Ford Taurus

1 Answer

2010 chevy equinox right rear turn signal doesnt work, replaced bulb and still the same. front works, is there a fuse for the rear light and where is the fuse located.


RT/SIG fuse #11 15amp - I/P fuse box . Fuse Block - I/P
In the center of the instrument panel, beneath the right side of the radio, in back of the right side console access panel.
This fuse is power to the BCM , When you put on the right turn signal , this is a voltage signal to the BCM . With logic ( programming ) the BCM then controls the turn signal !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
There could be a DTC- diagnostic trouble code stored in the BCM pointing to the problem ! I suggest you take your vehicle to the dealer or a ASE certified repair shop that has the diagnostic tools to find the problem . Just so you don't waste your money replacing parts that don't fix it.
There could

Dec 14, 2012 | 2005 Chevrolet Equinox

1 Answer

Where turn signal flasher fuse located on a 1997 monte carlo?


COMBINATION TURN SIGNAL AND HAZARD FLASHER MOUNTED TO FIREWALL TO THE LEFT OF THE STEERING COLUMN UNDER THE INSTRUMENT PANEL.FUSE TO TURN SIGNAL FLASHER IS IN FUSE BOX ON THE PASSENGER COMPARTMENT RIGHT SIDE OF THE INSTRUMENT PANEL.LOOK AT THE FUSE COVER IT WILL TELL YOU LOCATION OF FUSE FOR CIRCUIT IT CONTROLS.YOU ALSO HAVE FUSES IN THE ENGINE COMPARTMENT NEXT TO WINDSHIELD WASHER FLUID RESERVOIR.

Sep 09, 2010 | 1997 Chevrolet Monte Carlo

2 Answers

Where do i find the flasher for the indicator? the left light wont come on even thogh we bought a new bulb


Flashers and Relays REPLACEMENT Pickups The hazard warning flasher, on the pickup, is located to the left of the steering column, beneath the instrument panel, and is secured by a clamp and one screw. To remove it, simply unplug the electrical connector, loosen the screw, and slide the flasher out of the clamp. The turn signal flasher is located to the right of the steering column, beneath the instrument panel, and is secured in the same way as the hazard flasher. The turn the signal relay is located to the immediate right of the hazard flasher, and is secured by two screws. To remove it, unplug the electrical connector and remove the screws. MPV The relays and flashers are located under the dash, near the fusebox. Navajo Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel. The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel. prev.gif next.gif

Jul 15, 2010 | 1992 Mazda B-Series

1 Answer

Turn signal flashers will come on but won't blink


For 1994 Buick Lesabre 3.8L SFI OHV 6cyl the turn signal flasher is under the instrument panel to the left of the steering column brace. On the Bonneville, it may be on the left side on the shroud. The hazard flasher is under the instrument panel to the right of the steering column.

The turn signal flasher is installed in a clamp attached to the base of the steering column support inside the car. In all cases, replacement is made by unplugging the old unit and plugging in a new one.

Hope helped (remember rated and comment this).

Mar 03, 2010 | 1994 Buick LeSabre

2 Answers

I need to know where the flasher unit is on my 87 Caravelle


Hello cmason1.
If you are speaking of the signal light flasher it is located in your fuse panel which is under your instrument panel on the left of the steering column.
The hazard warning flasher is clipped to the instrument panel below the fuse block.
I hope this leads you to your repair.

Nov 26, 2009 | 1987 Plymouth Caravelle

2 Answers

Location of flasher for turn signal


  1. Access the COMBINATION Turn Signal and Hazard INDICATOR FLASHER on the Left-Hand (drivers) side of the instrument panel in the fuse junction panel.
  1. Remove turn signal flasher/hazard indicator flasher by pulling indicator flasher straight out.
  1. To install, align the terminals of the flasher and press into place.
How about a picture--

388df46.gif

Oct 03, 2008 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...