Question about 1994 Ford Explorer Limited

2 Answers

Anti-theft system Can't find location to disconnect anti-theft system. System goes off on it's own.

Posted by on

  • 1 more comment 
  • Glen McCart May 11, 2010

    Is this factory or aftermarket?

  • Henry KAo May 11, 2010

    is it a factory system?

  • jason brokken Jan 03, 2012

    factory system siren was yanked from its connection under hood and i need to reinstall and connect. where does it connect intp

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My wife locked her keys in and it is the only set. we have a 1994 ford explorer eddie baure edition. it is equiped with an anti theft system on it . if u or someone else has jimmyed the lock on one of the doors that may be your problem. on the lock is a senser and if that senser is not on there then the alarm will go off every time you open that door. so you have to take the door panal off and put it back on. if you don't know how to put it back on then take the opposite door panal off to see how it goes on. hope that helps you out

Posted on Apr 21, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

First is this an after market system? If so you will have to find the box under the dash and disconnect it. also if it has starter disable you will have to repair the wires that the installer cut to install that feature. If it is the factory alarm it is behind the dash.

Posted on Mar 21, 2009

2 Suggested Answers

ghost4548
  • 776 Answers

SOURCE: Hello accent 2004 with anti theft system battery flat anti theft

Have you verified this system is running the battery down? The system you describe is called the Remote Keyless Entry System (Electronic Time/Alarm & Control System - ETACS Module). It cannot be 'disconnected' without disabling other systems (intermittent wipers, Chime bell, Door Warning, Dimming Off Room Lamp, Seat Belt indicator, remote power door lock/unlock system, etc.)

f92f17f.jpg

Posted on Jun 29, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the exact location of the antitheft fuse box?


Explain anti-theft fuse box ! what do you think this is ? There is an anti-theft system on your vehicle , called PATS - passive anti theft system .Sorry , but there is not anti-theft fuse box .
Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:
  • theft indicator
  • encoded ignition key
  • PATS transceiver module
  • powertrain control module (PCM)
  • standard corporate protocol (SCP) communication network

Mar 20, 2016 | 2004 Ford Ranger

1 Answer

How to disconnect anti theft


It is hard to give a definite answer because I don't know which and how many wires were damaged...Anti theft can be a real HEADACHE.....You can begin by disconnecting battery cables..Use your VIN number for parts,Get new ignition with a programmed factory key from dealer only.....They probably blew certain fuses and or relays when this happened...Or maybe not..Install new ignition connect battery cables..,turn switch on just to check for bad fuses and relays...Disconnect battery again...replace any fuses blown...Connect battery again...( Each time you disconnect battery it resets the computer system and should clear anti theft codes..)..make sure all doors are unlocked by using door remote key fob....Now see if vehicle will crank..If all is done correctly it should start...However I don't know how much damage was done.....It may possibly be too much work to totally disengage anti theft....You could start with removing all fuses and relays related to anti theft but disconnect battery before...I DO NOT RECOMMEND trying to disable the theft system.....You may create more headaches that you want.......Begin by trying what I described just to be safe...!!....

Jan 27, 2015 | 2001 Ford Windstar

2 Answers

89 firebird anti theft code won't let car start


If code 53 involves the PASS system for your car, the chip in the key has failed, or the sensor in the lock cylinder, or the control module.
The anti-theft system disables the starter and the fuel injectors. You could bypass those circuits to get the car started.

Oct 02, 2012 | 1989 Pontiac Firebird

1 Answer

Rx8 2008-My battery was dead after being stored for 5 months. I did not not disconnect the battery (I know I should have). I had my battery jumped with my husband's car. As soon as I connected the cables...


You should have disconnected the battery and fully charged it before starting the car.
The low voltage may have damaged some of the electronic components in the alarm system.
Charge the battery fully, then reconnect it and see if that helps.

Apr 16, 2011 | 2006 Mazda RX-8

1 Answer

Car won't start.Theft light blinks,clicking sound under hood and thumping like horn wants to go off.Seems like it's stuck in anti theft mode


anti theft light should blink every few seconds.

try disconnecting the battery for 15 minutes.

Anti-Theft-Perimeter The perimeter anti-theft system consists of the following components:
  • anti-theft indicator (THEFT)
  • remote anti-theft personality (RAP) module
  • hood switch
  • keyless entry remote transmitter
  • deck lid ajar switch
NOTE: The remote entry features will not function when the ignition switch is in the RUN or ACC position.
Up to four keyless entry remote transmitters (15K601) can be programmed at one time.
The keyless entry remote transmitters :
  • Are programmable.
  • Must be set at the same time.
  • House four buttons.
  • House three buttons (Mexico Anti-Theft System only).
Programming
Refer to Section 501-14B.
Inputs and Outputs
The remote anti-theft personality (RAP) module receives input from the following components for anti-theft operation:
  • Hood switch.
  • Deck lid ajar switch.
  • Keyless entry remote transmitter.
  • Power door lock switches (LH and RH).
  • Door courtesy input.
The RAP module distributes output to the following for the anti-theft system:
  • Power door unlock relay.
  • Power door lock relay.
  • Liftgate unlock relay (Wagon)
  • Park lamps relay.
  • HORN relay.
  • Dome lamp.
  • THEFT indicator.
  • Deck lid release.
Arming
The anti-theft system can be armed if:
  • The ignition switch is in the OFF position.
  • The panic alarm is off.
  • All doors are closed.
NOTE: If a door is open, the anti-theft system is prearmed and waiting for all the doors to be closed. The THEFT indicator will remain illuminated for up to 30 minutes waiting for all the doors to be closed. If a door remains open after 30 minutes, the THEFT indicator will turn off and the system will return to a disarmed state. After all doors are closed and the 30 second prearm (continuous THEFT indicator illumination) is complete, the system is armed.
NOTE: If the theft LED does not flash after 30 seconds, check the LED FLASH PID to see if the feature is enabled.
The anti-theft system will be armed when the lock button on the keyless entry remote transmitter is pressed, all doors are closed and 30 seconds have elapsed.
When the system is armed, the THEFT indicator will flash quickly until the system is triggered or disarmed.
Disarming
NOTE: Using a key in a door lock cylinder to unlock is not a valid method of disarming the anti-theft system.
Untriggered System
NOTE: If the driver arms the system and remains in the vehicle, an untriggered system can be disarmed by turning the ignition switch to the ON position.
An untriggered alarm system can be disarmed by pressing the unlock button on the keyless entry remote transmitter.
Triggered System
NOTE: If the hood or trunk are open when the system is armed, it must be closed and opened again before it can trigger an alarm.
An armed anti-theft system can be triggered by the following conditions:
The deck lid door, liftgate, hood or any door is opened using a key, inside door handle, hood release, etc.
  • The keyless entry remote transmitter can activate a panic alarm which is similar to the anti-theft alarm, but does not cause the THEFT indicator to flash.
A triggered alarm system can be disarmed by:
  • Pressing the unlock or panic button on the keyless entry remote transmitter.
  • Turning the ignition switch to the ON position.
Alarm State When Battery Power Is Cycled
When the RAP module is supplied power the first time at the vehicle assembly plant, the system will be in the disarmed state. The RAP module will remember whether it is armed, disarmed or triggered in its non-volatile memory. When the battery positive cable is removed and then reconnected, the system will return to the state it was in just before the battery was disconnected. If the system is in any prearm state, then the system will return to a disarmed state when the battery is disconnected and then reconnected.

Nov 06, 2010 | 1999 Mercury Tracer

1 Answer

Hello accent 2004 with anti theft system battery flat anti theft


Have you verified this system is running the battery down? The system you describe is called the Remote Keyless Entry System (Electronic Time/Alarm & Control System - ETACS Module). It cannot be 'disconnected' without disabling other systems (intermittent wipers, Chime bell, Door Warning, Dimming Off Room Lamp, Seat Belt indicator, remote power door lock/unlock system, etc.)

f92f17f.jpg

Jun 10, 2009 | Hyundai Motor 2004 Accent

1 Answer

Trouble starting once in awhile


it does sound like the anti-theft system. There are only 2 ways to bypass your problem. 1) disconnect the anti-theft system which runs into your ignition, cut the wires to the system and join them back together without hooking it back up to the anti-theft. 2) Bring it back to the dealer so that they can replace your anti-theft sensor. The part is rather cheap but the labor is the killer.

Apr 11, 2009 | 1997 Pontiac Grand Am

1 Answer

VEHICLE WONT START


Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:
  • protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
  • monitors the status of the ignition key lock cylinder.
  • is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
  • when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
  • protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
  • triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.
Once triggered, the system responds by:
  • flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
  • sounding the horn (13832).
  • disabling the starter circuit until the system is disarmed.
---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module
  • The remote anti-theft personality module is located behind the instrument panel (04320).
  • It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
  • The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.
-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove radio. Refer to Section 15-01 .
  1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
  1. Lower glove box.
  1. Remove two remote anti-theft personality module bracket retaining screws.
  1. Disconnect electrical connectors and alarm and lock system antenna (15603).
  1. Remove remote anti-theft personality module and bracket.
  1. Remove remote anti-theft personality module from mounting bracket.
Installation
  1. To install, follow removal procedure in reverse order.
  1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).

    34bdf35.gif
Components The system is composed of the following components:
  • remote anti-theft personality (RAP) module with integral antenna
  • alarm indicator LED
  • door lock cylinder switch RH, door lock cylinder switch LH
  • liftgate door lock cylinder switch (220A40)
  • hood switch (part of windshield wiper motor wiring (17A477))
  • ignition lock anti-theft switch (19A438)
The following vehicle components are also used by the anti-theft alarm system:
  • generic electronic module
  • power door lock switch (14028)
  • door open warning lamp switch (14018)
  • autolamp relay (14N089)
  • horn relay and bracket (13853) and horn (13832)
  • low beam headlamps
  • rear lamps (13404) and parking lamps (13200)
  • starter relay
  • door lock relays
  • keyless entry remote transmitter (15K601)
--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:
  1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
  2. Unlock any door with a key.
  3. Turn ignition switch to RUN or ACC.
  4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.
------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:
  • Open any door or liftgate.
  • Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
  • Dislodge the ignition key lock cylinder.
  • The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.
When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

  • low beam headlamps
  • parking lamps
  • horn
  • THEFT indicator
The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

Mar 02, 2009 | 1998 Ford Windstar

1 Answer

1996 CHEVROLET CAVALIER.


It is probably not the anti theft system if it cranks over fast then slow it is your timing chain. If you want to try resetting the anti theft system disconnect the battery cables for 24 hours and reconnect them.

Nov 01, 2008 | 1996 Chevrolet Cavalier

1 Answer

I need to disconnect the anti theft 94 explorer


Refer to the owners manual and remove the fuse for the security system. If there are other necessary features tied into the fuse, then you will need to locate the security system control module under the dash or on the firewall, and disconnect or cut the wires leading to it.

Aug 08, 2008 | 1994 Ford Explorer Limited

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

744 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...