Question about 2004 Chrysler Sebring

1 Answer

Remove and replace convertable top on a Chryster Sebring

We want to replace the convertible top on our Sebring. We have a replacement top that has the frame and everything. The hydraulic lines have been cut, on the replacement top, so we will use the old ones. How do we get the old top off, so we can put the new top on? On the replacement all that we have to do is glue the back window in.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Albert I need to tell you this buddy you have saved some money on the top I would call a uphostry shop in your area they will pick up car and repalce the top for you and the window needs to be seemed in there for safety reasons call one up I hate to tell you that but. Your better off having a specailty company do this if you need anything go to

Posted on Mar 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove driver door panel on 2004 Sebring convertible to replace external door handle

Panels usually push on with plastic clips or screws,some screws are hidden behind push in plug covers.

Jul 20, 2014 | 2004 Chrysler Sebring Convertible

1 Answer

How to remove silencer cover on 1999 crysler Sebring convertible passenger side

should be held in with screws under dash pull down and the rezistor should be close to teh center console on teh botum of teh heater box

Feb 06, 2014 | Chrysler Cars & Trucks

2 Answers

How to find 2000 Chrysler jxi convertible top motor

sebring transmission pan torque spec need torque specs for 2000 Sebring jxi convertible, transmission pan torque specs and bolt tighting

Nov 29, 2011 | Cars & Trucks

1 Answer

I have a 1996 chryster Sebring Convertible jxi 2.5L 6cy startes and runs ok but when u go to drive sometime it goes and sometimes it dies

I have a car just like yours. My car use to do the same thing. When I checked for a code, it showed nothing. I would be driving down the road, sometimes 50-60, and it would just cut off. I bought a MAP sensor and that fixed my problem. Hope that helps.

Oct 18, 2010 | 1996 Chrysler Sebring

3 Answers

Is the fuel filter external or internal on a 2000 chrysler sebring convertable. 2.5 V-6?

The fuel filter is external, will be an in-line fuel filter meaning it's screw into the fuel line, more then likely will be under the hood over by the fire wall.

Jun 08, 2010 | 2000 Chrysler Sebring

1 Answer

Replacing the back window in a 2002 convertible

The rear window in your car is a separate part from the top so it can be replaced without replacing the top.
You must, however remove most of the top.
Windows are available on Ebay and instructions are available on DVD here.

Regards, Karl

Oct 28, 2009 | 2002 Chrysler Sebring

1 Answer

Just bought /used 1996/ back window is hanging how do i replace

have to remove the top to restich in window....and with labor cost so much you might just as well replace whole top...

Aug 16, 2009 | 1999 Chrysler Sebring

1 Answer

Bleeding hyd system on 05 sebring convertible top

You are probably low on fluid.
Behind the rear seat is your motor/pump/reservoir combination.
With the top down, fill the reservoir to overflowing with ATF.
Cycle the system a few times and repeat.
Do this till the reservoir will take no more fluid.
Check the lines and cylinders for leaks. If you replace any lines or cylinders, always do them in pairs.
Karl at

Apr 08, 2009 | 2004 Chrysler Sebring

2 Answers

Timing marks for chryster sibring 2003 2.7L

Here's a link to 98' - 2004 Intrepid 2.7. If you have dual cam etc. and all looks same, you should be o.k. Take a real good look at picture. If you click on it when you get there, it expands.

Dec 22, 2008 | 2003 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

1,276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides