Question about 1988 Chevrolet Cavalier Z24

2 Answers

Clutch slave cylinder

Is the slave cylinder external or internal

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Awesome link thanks a lot !!!

Posted on Mar 21, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace clutch slave cylinder

more information required as to make and model and year as cars now have an external slave cylinder and an internal slave cylinder that requires the gear box removal to fix.

Mar 01, 2015 | Cars & Trucks

1 Answer

I just replaced my master clutch cylinderin my 2008 lancer a week ago,paid 400. Now they're saying its the slave cylinder and they have to pull the transmission out and get deep into it and...

You could have either an internal [concentric] clutch slave cylinder or an external slave cylinder depending on which transmission Mitsubishi used for your car. The problem is that automobile manufacturers all source parts from wherever they can and from each other.
The video shows an external and easy [relatively inexpensive to replace slave cylinder. An external slave cylinder shouldn't cost more than $40 in parts and less than one hour of labor to replace. A look under your car may save you lots of money. Also look for a reliable independent repair shop rather than the dealer to save money.
Then there is the centric slave cylinder that fits around the transmission input shaft [requiring transmission removal to replace].
If you have this type of slave cylinder, you are in for close to $100 in parts and 5 to 6 hours of labor.

Jan 31, 2015 | Cars & Trucks

1 Answer

Clutch fade if you keep your foot on the clutch then you must take your foot of the padel and then you can put your foot down on the padel if you keep your foot to long on the padel it fades agian help...

There's a problem with your clutch hydraulic system, either the clutch master cylinder or the slave cylinder. See if the reservoir is full (takes brake fluid), and if very low, may have a leak and should be bled down at the slave cylinder. And check for external leaks, as that is likely the cause of brake fade. If no external leaks, and filling the reservoir did not help, then either the master or the slave has a seal that is not holding pressure, but leaking internally.
I don't know if there is any way to test to see which is bad, so you might try a new or used slave cylinder first, it's cheaper than the master.

Aug 29, 2013 | Cars & Trucks

1 Answer

Replace slave cylinder

okay, lets hope the clutch slave is installed correctly, is this slave internal or external. in other words can the clutch slave(the part that pushes clutch fork) be replaced with out pulling the transmission?
what year,make and model is this car? did you open the clutch line? how did you bleed the clutch?

May 05, 2013 | Cars & Trucks

1 Answer

How do i tell if my 1995 slave cylinder is internal or external

slave cylinder is at wheels or brakes most are internal meaning you have to remove brake drum to access them .slave cylinder on clutch usuall external

Feb 14, 2011 | 1995 Chevrolet Cavalier

1 Answer

Is the clutch slave cylinder internal or external of transmission?

external if it's like my 1979 Honda. Internal if like the following information:
Slave Cylinder on 1999 Chevrolet Cavalier
  1. Disconnect the negative battery cable.
  2. Detach the master cylinder assembly from the actuator cylinder by disconnecting the hydraulic line.
  3. Remove the transaxle assembly, as outlined earlier in this section.
  4. Remove the clutch actuator cylinder from the transaxle. Fig. 1: Clutch actuator cylinder assembly mounting 91147g02.gif
    To install:
  5. Lubricate the inside diameter of the bearing with clutch bearing lubricant GM part no. 12345777 or equivalent.
  6. Install the actuator cylinder in the transaxle, then install the transaxle assembly.
  7. Connect the master cylinder-to-actuator hydraulic line.
  8. Bleed the hydraulic system, as outlined later in this section.
  9. If removed, install the air intake duct.
  10. Connect the negative battery cable.
prev.gif next.gif

Jun 20, 2010 | 1999 Chevrolet Cavalier

1 Answer

No fluid in clutch resevoir

If you have an internal slave cylinder check it for leaks or if an external slave cylinder check it for leaks. Check the back side of the master cylinder where it attaches to the firewall and see if the seals are leaking. If so replace the master or rebuild it. Same with the slave cylinder.

Aug 15, 2009 | 1994 Jeep Wrangler

3 Answers

Do i have to remove the transmission to change the slave cylinder


Jun 25, 2009 | 1990 Jeep Wrangler

1 Answer

Slave cylinder or clutch? or both?

it internal and pretty much alot of work. You have to pull the transmission out

Jul 24, 2008 | 1995 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides