Question about 1997 Toyota Land Cruiser

1 Answer

Front door panels

REady to replace front speakers in my 1997 Landcruiser - do I need to remove the door panels?  If so, what's the best way to do it without doing any damage?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 104 Answers

Yes you need to remove the door panel and here is the instructions via TIS (Toyota info system)

DISASSEMBLY
1. REMOVE THESE PARTS:
HINT:
Tape a screwdriver tip before use.
(a) Door inside handle bezel
(b) Armrest
(c) Armrest panel base upper
(d) Courtesy light
(e) Lower frame bracket garnish
2. REMOVE DOOR TRIM
(a) Remove the 3 screws from the door trim.
(b) Using a screwdriver, remove the clip and remove the trim
by pulling all of the trim up.
HINT:
Tape the screwdriver tip before use.
(c) Remove the 11 screws and armrest base from the door
trim.
(d) Remove the inner weatherstrip from the door trim.
(e) Remove the 8 screws and door pocket from the door trim.
3. REMOVE THESE PARTS:
(a) Door belt moulding
HINT:
Pry out the clip from the edge of the panel, and remove the
moulding .
(b) Door weatherstrip
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
(c) Door inside handle
(d) Door lock control relay
(e) Service hole cover
BO2455
Cotton
Tape
Panel
Cover
BO−10
BODY − FRONT DOOR
NOTICE:
Do not block the trim clip sealing with the tape.
(f) Outside rear view mirror
(g) Door glass run
(h) Rear lower frame
HINT:
Adjust the equalizer arm up to down and tighten if where dimensions
A and B, as shown are equal.
(i) Door glass
(j) Window regulator
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
Apply MP grease to the sliding surface and gears of the window
regulator.
NOTICE:
Do not apply grease to the spring.
(k) Locking and opening control link
(l) Door lock
HINT:
Apply adhesive to the 3 screws.
Part No.08833−00070, THREE BOND 1324 or equivalent
Torque:5.0 N·m (50 kgf·cm, 43 in.·lbf)
BODY − FRONT DOOR
BO−11
HINT:
At the time of reassembly, apply MP grease to the sliding surface
of the door lock.
(m) Door outside handle
(n) Door lock cylinder
(o) Door speak

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace front drivers side window motor 1997 mercury mystique


The motor and regulator need to come out here is how to do that.

Instructions
    • 1Gently remove the door panel of your Contour, ensuring that you don't break the three door clips that hold it on. As you pull the panel from the door, support the panel from below. This will ensure that none of the wiring inside the door is damaged. Release the wiring from the components inside the door, including the power window mechanism, power lock mechanism (if equipped) and the stereo speaker. Place the door panel in a safe area with the clips so they are accessible when you are ready to replace them.
    • 2Remove the window glass by sliding it up and out of the door. Support the glass from the bottom so it doesn't drop and break. Window glass for a Contour can cost around $150 to replace. After you remove the glass, put it in a safe place. You may want to wrap it in old towels or blankets to protect it until you are ready to reinstall it.
    • Sponsored Links
    • 3Unplug the wires from your Contour's window motor, and remove the screws from the window motor and regulator. Remove the power window motor and regulator from your Contour to make way for the new parts.
    • 4Install the new window regulator into the door, and replace the screws that held them in place.
    • 5Replace the window glass into the door, and connect it to your Contour's power window motor and regulator assembly.
    • 6Replace the door panel. Reconnect the wiring for the power window and power lock controls, and replace each clip that connects the panel to the door.

Jul 01, 2012 | 1998 Mercury Mystique

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

I just need to know if on the back of the 1997 camaro if there are audio plugs


the stock wiring is bare bones:
1997 Chevrolet Camaro Car Stereo Wiring Schematic
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: Yellow
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Gray
Car Stereo Dimmer Wire: Brown
Car Stereo Antenna Trigger Wire: Pink
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 6 1/2?
Car Audio Front Speakers Location: Doors
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: 6 1/2?
Car Audio Rear Speakers Location: Side Panels
Left Rear Speaker Positive Wire (+): Yellow
Left Rear Speaker Negative Wire (-): Brown
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

Sep 24, 2010 | 1997 Chevrolet Camaro

1 Answer

1997 mercury villager passenger side mirror replacement guide. how do i do it? is there an easy access panel or does the whole door panel need to be removed


door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure. Body Side
Removal
  1. Gently pry loose the body side door latch handle bezel and remove it.
  1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).




Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
Installation
  1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
  1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.

May 22, 2010 | 1998 Mercury Villager

1 Answer

HOw do I replace front speakers on 1991 brougham?


you'll need to remove the door Panel to access the door speakers,the door panel will be held in with several screws.

I believe the Front Door Speakers in a brougham of that year are 4x6".

Mar 04, 2010 | 1991 Cadillac Brougham

2 Answers

I NEED NEW SPEAKERS FOR MY FRONT DOORS IN MY HONDA CIVIC COUPE 1997 BUT DONT KNOW WHAT SIZE TO BUY?


Not sure if you had a sedan, hatch, or coupe but here is the info you requested. Front door speakers measure 6.5" with a top depth of 1.75" (you have no depth problems here but any larger than 1.75 and you might have to cut out the factory housing.)

If they are door or kick panel speakers, you have to remove that panel to extract the speakers. Then measure them with a ruler; better yet, make a pencil outline of them (outside rim) and also where the mounting holes are. Then, when you buy new speakers say at Best Buy or some such, you will get the proper size, mounting and DEPTH. Unless you want to build all new mounting enclosures, you have to be sure of all the size measurements so that your new speakers will fit.

Wiring them is easy. There should be instructions. Speaker wires do have a + and - side, and if you cross them, the speakers will work but won't sound as good. Also be sure you have the POWER to drive your new speakers. Buy speakers of the same "impedence", measured in ohms right on your speakers.

Also, in here you can find the 1997 Honda Civic Service Manual.

Easy job, good luck (remember rated this help).

Oct 14, 2009 | Honda Civic Cars & Trucks

2 Answers

I am looking for a diagram or picture as to how to get to the speakers to replace them on a 97 villager??


Section 15-03: Speakers 1997 Villager Workshop Manual DESCRIPTION AND OPERATION Radio Speakers All vehicle sound systems are equipped with radio speakers (18808) located at all four corners of the vehicle. The radio speakers are mounted in the RH front door (20124) and LH front door (20125), as well as behind the quarter trim panels (31012) in the rear of the vehicle. The Ford Super Sound Audio System has the addition of a subwoofer mounted in the RH quarter trim panel.
-----------------------------------------------------------------------------------------
Radio Speakers, Front Door Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 .
Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  2. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
  3. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  2. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  3. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  4. Remove the front door trim panel.

Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
  1. Remove the four front door radio speaker screws.

May 20, 2009 | 1997 Mercury Villager

1 Answer

How do you replace the front door speakers in a 1999 Model Hyundai Excel?


You have to take the door panels off.
The front speakers are 6"
So remove the front door panels, unbolt the factory speakers, bolt the new one in the existing holes, reinstall the door panels.
The grills will look factory, but you will have better speakers. Nice way to keep the good stuff hidden from prying eyes.

Oct 19, 2008 | 1994 Hyundai Excel

2 Answers

Front door speakers


I just replaced mine on my 2002 Diamante LS yesterday. It really isn't that difficult. To get to the front door speaker you will need to remove the door trim panel. This is done by pulling out on the bottom part of the panel. I used a flathead screwdriver to help with the separation. Just be careful not to scratch anything.

There are 4 or 5 clips that lock the panel on to the door frame. After you have pulled the clips out you will want to lift up on the separated panel as it hangs on a rail adjacent to the window. Pull the panel out far enough to reach behind and disconnect the various wiring clips. They have quick disconnect fittings and come out easily. You will also need to disconnect the door interior light by rotating the base about a half turn to get it out of the removable panel.

Once you have removed the door panel you will have full access to the speaker frame mounting. It has a removable plastic frame that you screw the new speakers in to. It attaches to the door frame with 5 or 6 Phillips type screws. I found it easier to remove the mount and get it ready to accept my new speakers. I just srewed it back on before actually attaching the speakers.

While the dealer spec for door speakers on a Diamante is a 6 3/4" speaker, a 6 1/2" will work just fine if you have a drill to pre-drill new screw holes. Just line the new speaker up on the speaker mount, mark where the new holes should be and then go ahead and drill them. Make sure the drill bit isn't bigger the the screw. It is a machine type of a thread and is easy to self thread with a regular phillips screwdriver.

After you have the speaker mount ready to accept your new speaker you can go back to your car, screw the mount back on to the door frame. Next attach the two speaker wires to the back of the new speaker. White goes to the positive post. (You might need to change the fitting type to match the car wiring and the new speaker) You can get some quick connect friction fittings and put one on the end of each wire that attaches to the speaker. Walmart, Autozone, Radio Shack all have these as they are readily available.

With the speakers in place, just reverse you installation of the door panel. I found it was easier to roll the window down so I could hang the panel back on the channel. Line up the clips and the bottom of the door, push in and you will feel and hear them engage. Once you are sure they are lined up correctly, go ahead and give it a good push where each clip attaches to make sure its on tight.

All done, enjoy your new sound system.

Oct 02, 2008 | 2004 Mitsubishi Diamante

Not finding what you are looking for?
1997 Toyota Land Cruiser Logo

529 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...