Question about 2000 Toyota 4Runner

1 Answer

One out of 4 of the auto locks wont lock or unlock. Motor sounds fine. Wont lock with the auto key remote. Wont lock with the lock/unlock button on the door panel. Can only lock manually or with the key in the key hole. My vehicle is a 2000 toyota 4 runner.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Replace the door lock actuator, it is bad.

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can hear it click but it wont open with the key either.


Auto Repair : Power Door Lock Troubleshooting - YouTube

? 1:52
https://www.youtube.com/watch?v=wsqbE_ztTYw
May 12, 2009 - Uploaded by ehowauto
Hi i have a locked driver side door that will not open.when i lift the locking ... I press the power lock, and hear a sound but all four doors remain locked or unlocked ... Hey sorry for the botherbut I need help.my key button don't unlock or lock.the button inside the car doesn't work either to unlock or lock.so I'm ...

Fixing A Car That Does Nothing When You Turn The Key ...

? 3:37
https://www.youtube.com/watch?v=TSE0fOrujW0
Aug 16, 2012 - Uploaded by Scotty Kilmer
2005 Mustang wont start or crank from the key.. wont say nothing good battery ..... all I hear is clicking noise my radio and lights and everything comes on but it will not do nothing what couldthis be have I blown something?

Jan 06, 2016 | Cars & Trucks

1 Answer

Xj8 door lock


You need to replace the lock actuator in the doors that are not locking/unlocking with the door switch/remote. If the remote works for most of the doors then it is fine. The actuator is what moves the lock when it gets the signal from the remote or door switch to move it.
Good luck

Jul 11, 2013 | Cars & Trucks

1 Answer

On my 2006 Chrysler 300/ the auto lock button on my key remote doesn't lock or unlock doors?


how do I reset one of two keys that the unlock,lock,trunck does't work but the key turns the engine over.

Oct 08, 2012 | 2006 Chrysler 300

1 Answer

2001 Santa Fe.Remote keyless stopped working.No lock, no unlock. Replaced transmitter battery, LEDs light up as usual. Manual key and manual lock/unlock switches work fine. Thanks in advance!!


some time the buttons on the remote get worn out and it will light up but it wont unlock or lock. you can just buy a new case and switch the piece inside. If you have another remote try to see if that one works if it does then the remote case is your problem

Feb 14, 2010 | Hyundai Motor 2003 Elantra

1 Answer

Hi, my central locking wont unlock the boot (renault clio 2002).


Its sounds like a sticky boot lock it wont be the remote, open the boot with the key and spray all around the lock and lock mechanism with WD-40 then lock and unlock keep repeating unlock, lock using both the key and remote it should free off.

Be sure to use plenty of WD-40 on the underside of the boot lid into the mechanism dont be shy with it.

Hope this helps.

Jan 22, 2010 | 2003 Renault 181

1 Answer

I replaced battery in my audi 80 2.0 tdi but have lost the remote and alarm wont stop going off .


Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction: Alarm LED in rear fog lamp switch illuminates for 30 seconds when vehicle is locked.
How
NOTE: A maximum of 4 keys can be programmed (one at a time).
As memory positions of existing keys are unlikely to be known: Obtain and reprogram all keys.
NOTE: Existing key memory positions will be overwritten.
Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Using first key, press unlock button once (programs memory position 1). Alarm horn sounds once to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF. To program remaining keys into memory positions 2, 3 and 4. Carry out the complete procedure below for each key: Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Press unlock button at 1 second intervals, as follows: Twice for memory position 2 (second key). Three times for memory position 3 (third key). Four times for memory position 4 (fourth key). Alarm horn sounds once every time unlock button is pressed, to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF.
NOTE: Ignition MUST be switched OFF between each key programming procedure

Jan 10, 2010 | 1992 Audi 80

1 Answer

My renault laguna 1999 rt remote key fob wont work?


IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Jul 09, 2009 | 2004 Renault 181

1 Answer

Drivers door power lock wont work.


Either the wring going to that motor or the motor itself is bad.

Mar 08, 2009 | 2000 Toyota 4Runner

Not finding what you are looking for?
2000 Toyota 4Runner Logo

422 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...