Question about Ford Econoline Wagon

1 Answer

Hazard ligts working....not directionals. Checked all fuses as best I could. Location of fuse block is difficult to get at.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Sometimes the hazards run on a different circuit than turn signals. There is probably a fuse that needs to be replaced. If no fuse, make sure that the turn indicator is working properly. After that look for broken wires along the circuit.

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals quit working we checked fuses and bulbs and put new turn signal switch but still not working


Not the best picture for location. If you have another flasher for comparison it will help.
turn-signals-quit-working-checked-fuses-bw0yv2jqta4x2gnwod1jf1eh-3-0.gif

Jul 12, 2015 | 1992 Chevrolet Lumina

2 Answers

My turning signals not working on gms 1999 savanna van


Hi Mary , do the hazard lights work ? Did you check fuse #16 TURNB/U 20amp. in the instrument panel fuse box ? IP Fuse Block ,In the left lower kick panel. If the hazard lights don't work either bad flasher relay !

Apr 06, 2015 | 1999 GMC Savana

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

I need fix the hazard ligts & turn ligts I check all fuses but now I want see the harnes diagram


Those are both driven by a relay built into the hazard switch. Replace the switch and everything will work again.

Jul 21, 2010 | 1995 Volkswagen Jetta

1 Answer

2000 Chevrolet 2500 hazard flasher location. Is


hello. the hazard flasher is the same as the turn flasher. it is mounted behind the left ip fuse block.


9b682fe.gif

Oct 29, 2009 | 2000 Chevrolet 2500

2 Answers

I have a 1990 Chrysler New Yorker. The turn signals don't work. When I turn on the hazard lights they work. I believe it is the relay fuse for the turn signals. The one I cant find is not located in fuse...


If the lights work with the hazards, your problem is not a fuse. You need what is called a multifunction switch. It is the switch that the directional arm goes into. It can be difficult to replace,

Hope this helps

Oct 06, 2009 | 1990 Chrysler New Yorker

2 Answers

Brake Lights do not work and hazard button is stuck


I could not tell you how many times people have brought their cars into my shop and tell me that they had already checked all fues and they are OK, then I check the car and find a blown fuse or a fuse that is completely missing.

Your dash (Instrument Cluster) illumination lights are powered by the "PARK LP" fuse in the underhood fuse panel - it is fuse number 37 and should be a 20 Amp fuse. If this fuse is blown, your Park lights on the exterior of the car will also not be working. If they are working and your dash lights are not, then the problem is probably in your headlamp switch.

Your Brake lights are powered by the "STOP LAMP" fuse in the instrument panel (IP) fuse block it is a 15 Amp fuse.

Your Hazzard lights are powered by the "HAZZARD" fuse in the (IP) also a 15 Ap fuse.

If both of these fuses are good, then the most likely problem with your brake and hazzard lamps is the multifunction (Turn Signal) switch.

What any of the above has to do with replacing your window regulators remains a mystery.

Jul 20, 2009 | 2003 Pontiac Grand Prix

1 Answer

Have hazard lights but no running or turn signals


sounds like you need a combo flasher assembly..located in fuse block inside vehicle under steering column..there may be a plastic cover under dash you have to remove to see fuse block..large black relay that plugs into fuse block..if you pick up a new one,you will see what it looks like..available at dodge dealer..combo flasher or drl/signal relay

Jun 11, 2009 | 1999 Dodge Caravan

2 Answers

Hazard button and door lock button not working 325i 02


Your vehicle only has fuses behind the glove box. But since your central lock button is also inop. The your solution is to replace the switch assembly, it comes with both the hazard switch and the lock/unlock button. The removal of the switch assembly is pretty simple. it just pops up with some plastic body tool to pry on it.

Apr 01, 2009 | 2002 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...