Question about 1997 Kia Sportage

1 Answer

4 wheel drive issue

When I shift it into 4 wheel drive it goes into gear the light comes on but the whhels dont turn it acts like it is in 4wheel drive but the wheels dont pull any suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Check your vacuum lines behind the front wheels

Posted on Apr 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lincoln Navigator 4wheel drive 1998


See that this is an old problem. Some of the knobs could crack on the backside and allow the knob to rotate on the shaft without turning the shaft at all. If the knob is okay then go underneath the vehicle and disconnect the electric plug on the shift solenoid and Inspect for corrosion on the terminals. There is a problem which can happen if an indicator light burns out in the electric shift models. The length of the shift solenoid plunger is what determines whether you are in 2 wheel or 4 wheel drive, or high or low range. If the indicator light burns out, it changes the electric power and position of the shift solenoid plunger.

Dec 03, 2014 | 1998 Lincoln Navigator

1 Answer

Why abs and 4wheel lights come on when i start


read the operators guide yet,
seems not.

Aug 12, 2014 | 2010 Jeep Patriot Sport

1 Answer

96 explorer disengages 4wh low but does not engage 2wheel


Does it shift to 4wd high range ? If so then shift to 2wd . What is going on here is the transfer case motor is stopping due to the motor position sensor has gone bad which means that you replace the transfer case motor assembly. But if you wish to make it a 2wd for awhile then remove motor and manually turn shaft . This can be done by raising and supporting rear axle truck in park remove motor turn shaft slowly with pliers and rotating the play in drive shaft. There are stamped markings on back of case showing gear positions..

Mar 31, 2014 | 1996 Ford Explorer

2 Answers

My orange 4wheel drive light comes on when I'm in 4wheel drive in my 86 jimmy. Is that good or bad?


its a warning your in 4 wheel drive so you dont forget to take it out when your on the road its good if its on when your in 4 wheel drive

Jan 24, 2011 | 1986 GMC Jimmy

1 Answer

The low range light has come on its stuck on 4x4 and is slowing my truck down how do i fix this


you cannot run your truck normally in 4x4 low!!!! the low is designed to go slow slow.try shifting into neutral gear on column tap the high 4x4 then shift to reverse,back up 15feet then shift to drive.it should go into high 4x4 then if you want to go back to 2wheel high shift to neutral tap the 4x4 high until the light goes off,shift to reverse and back up 15feet then shift to drive and the 4wheel drive lights should all be off. then you'll be in 2x2 rear wheel drive. thank you for choosing fixya.com

Jan 22, 2011 | Ford Excursion Cars & Trucks

1 Answer

Change clutch


Sounds like transfer case issue if 4 wheel drive works and 2 wd does not. Clutch slippage would be worse in 4 wheel drive more than 2 wheel drive, more to push.

May 16, 2010 | 2003 Toyota Tacoma

2 Answers

When i turn the dial to 4wheel low the light


4 wheel low engages only when u shift trans into neutral or park never when moving it can cause transfer case damage.

Jul 16, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

How to shift into 4wd


Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

May 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

1987 Jeep YJ [Wrangler] so owner ship says''


Our Jeep Wrangler YJ's are equipped with a vacuum module on the front axle. It is used to engage the front axle when the transfercase is shifted into 4WD. Check the vacuum lines on the front axle to make sure they are connected. The passenger side axle shaft has a disconnect sleeve that is moved left and right by the vacuum.

Mar 01, 2009 | 1987 Jeep Wrangler

Not finding what you are looking for?
1997 Kia Sportage Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...