Question about 2000 GMC Sonoma Extended Cab

1 Answer

Oil pan how do you remove your oil pan, do you have to move your transmission back first?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

No you do not, but you have to lift motor up to get pan over oil pump .

Posted on Mar 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change transmission oil


Hi Peter, If your Camry has an automatic transmission, for normal driving the auto fluid should be changed every 40,000km, there should be a drain plug on the transmission pan that takes a 10mm hex drive or 17mm socket to undo. You have two choices after driving the car onto ramps or jacking up and supporting on jack stands so you can safely get under the car. 1 - You can loosen and remove the transmission drain plug to let the auto fluid drain out into a container (careful not to lose the sealing washer) refit and tighten the drain plug and washer again. Remove the auto transmission fluid level dip stick, using a suitable funnel pour about 2.5 litres of suitable new auto trans fluid back into the transmission via the dipstick tube (I believe they take dexron 2 of 3 type fluid). Start the car and move it onto a level surface. With the engine running, handbrake on and brake pedal applied, shift the transmission from park through every gear selection slowly into 1st gear, then back to park. Leave engine running. Wipe the dip stick & insert it back into the dip stick tube fully, remove and check where the fluid level mark is on the end of the dipstick. If the fluid level indicates low or does not show at all, add 100ml of additional fluid and recheck the level till the fluid reaches the full mark on the dipstick. 2 - The second option is everything in the first option but includes replacement of the transmission filter and pan gasket. I would only do this if the car had travelled high km or the pan gasket was leaking. At the point where you've drained the old fluid into a container and refitted the drain plug and washer, remove all the transmission pan bolts and the transmission pan. If you have the time to let the fluid drain overnight prior to removing the pan it's a good idea because once the pan is removed, fluid will continue to drip from the transmission. You'll need to remove the old pan gasket, some may be stuck to the pan and or transmission, a razor blade type gasket scraper can be good for this but be careful not to scratch either surface when cleaning off the old gasket. Remove the bolts/nuts that hold the transmission filter onto the bottom of the transmission. Careful caus more fluid may drain out of the transmission or filter once removed. Fit the new filter and filter tube gasket & bolts/nuts, careful not to over tighten. Fit new pan gasket, pan and bolts. Continue with fluid filling procedure from option 1. I would suggest you only use option one and remember to double check the drain plug is tight. Also, remember to dispose of the old fluid correctly. Cheers

Nov 30, 2013 | 1993 Toyota Camry V6

1 Answer

Where is transmission filter located in 2001 mitsubishi diamante located and how do i change it?


transmission filter in the bottom of transmission bolted to valve body.you need a large drain pan.place drain plug under transmission oil pan.remove transmission oil pan drain plug.let all transmission fluid drain out then screw back drain plug in oil pan.then you need to remove transmission oil pan then remove filter and replace pan gasket also.make sure you have right amount transmission fluid on hand.buy extra because if you short of fluid you cant drive car if fluid level too low.make sure you get the right amount fluid.torque pan bolts to 96 inch pounds.

Nov 10, 2011 | 2001 Mitsubishi Diamante

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

2 Answers

When changing the trans fluid on my 2004 Avalanche, I understand that you have to disconnect the trans lines from the radiator and run the engine until the fluid stops flowing. Is this correct? If so, do...


I didn't read about running the engine at all during the transmission fluid change. --- Removal & Installation 4L60E/4L65E To Remove:
  1. Raise and safely support the vehicle.
  2. Place a drain pan under the transmission.
  3. If equipped with a drain plug, drain the transmission fluid.
  4. If necessary, remove the bolts and position aside the range selector cable bracket for clearance while lowering the pan. It is not necessary to remove the cable from the lever or bracket.
  5. Remove the catalytic converter.
  6. Remove the oil pan bolts from the front and sides of the pan only.
  7. Loosen the rear oil pan mounting bolts about 4 turns.
  8. Lightly tap the oil pan with a rubber mallet in order to loosen the pan and allow the fluid to drain.
  9. Remove the remaining oil pan bolts.
  10. Remove the oil pan and the gasket.
  11. Remove the filter by twisting and pulling on it.
  12. Remove and discard the filter seal. The filter seal may be stuck in the pump; if necessary, carefully use pliers or another suitable tool to remove the seal.
  13. Clean the transmission and the oil pan sealing surfaces with solvent, and air dry. You must remove all traces of the old gasket material.
To Install:
  1. Coat the new filter seal with transmission fluid.
  2. Install the new filter seal into the transmission case. Tap the seal into place using a suitable size socket.
  3. Install the new filter.
  4. Install the oil pan and new gasket. Tighten the bolts alternately and evenly to 97 lb in (11 Nm).
  5. Install the catalytic converter.
  6. If previously removed, install the range selector cable bracket and bolts. Tighten the bolts to 18 lb ft (25 Nm).
  7. Apply a small amount of sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil pan drain plug, if equipped.
  8. Install the oil pan drain plug, if equipped. Tighten the plug to 13 lb ft (18 Nm).
  9. Lower the vehicle.
  10. Fill the transmission to the proper level with DEXRON® III transmission fluid.
  11. Check the COLD fluid level reading for initial fill only.
  12. Inspect the oil pan gasket for leaks.
4L80E/4L85E To Remove:
  1. Raise and suitably support the vehicle.
  2. Place a drain pan under the transmission oil pan. Drain the transmission fluid and install the plug. Tighten the drain plug to 13 lb ft (18 Nm).
  3. Support the transmission with a transmission jack.
  4. Remove the transmission crossmember.
  5. Disconnect the range selector cable end from the transmission range selector lever ball stud. NOTE: It is not necessary to remove the selector cable from the bracket.
  6. Remove the transmission range selector cable bracket. Reposition the bracket and cable.
  7. Remove the oil pan bolts. NOTE: The transmission oil pan gasket is reusable. Replace as needed.
  8. Remove the oil pan and gasket.
  9. Remove the magnet from the bottom of the pan, if necessary.
  10. Remove the oil filter and neck seal.
To Install:
  1. Clean the transmission and the oil pan sealing surfaces with solvent.
  2. Install the filter neck seal and filter.
  3. Install the oil pan gasket to the pan.
  4. Install the magnet into the bottom of the pan, if necessary.
  5. Install the oil pan and bolts. Tighten the oil pan bolts to 18 lb ft (24 Nm).
  6. Install the transmission range selector cable bracket. Tighten the bolts to 18 lb ft (25 Nm).
  7. Connect the range selector cable end to the transmission range selector lever ball stud.
  8. Install the transmission crossmember. Tighten the fasteners to 70 lb ft (95 Nm).
  9. Install the transmission mount nuts. Tighten the nuts to 30 lb ft (40 Nm).
  10. Remove the transmission jack.
  11. Lower the vehicle.
  12. Fill the transmission to the proper level with DEXRON® III transmission fluid.
prev.gif next.gif

Aug 26, 2010 | 2004 Chevrolet Avalanche

2 Answers

THE CAR STARTS, THE SHIFT LEAVER MOVES TO ALL THE POSITIONS BUT THE REANSMISSION NEVER ENGAGES AND THE CAR WONT MOVE.


how easily dies the shifter move? if it feels as if there is no pressure, then possibly the cable is broken. have you had the fluid level checked? maybe there is a leak you are unaware of.

Oct 08, 2009 | 2004 Ford Freestar

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

1 Answer

2001 hyundai transmission seems to buck as if almost staling and slips when excellerating from a stop


YOUR TRANS NEEDS A FILTER AND OIL CHANGE YOU CAN DO IT YOUR SELF JUST BUY A FILTER KIT REMOVE THE PAN AND DROP THE OIL UNDOO THE BOLTS AT THE REAR OF THE PAN AND SLOWLEY MOVE FORWARD THAT WAY THE OIL WILL RUN OUT OF THE BACK OF THE PAN MAKE SURE YOU HAVE A LARGE FLAT CONTAINER TO CATCH THE OIL
CHANGE THE FILTER AND RE FIT THE PAN YOUR TRANS SHOULD TAKE ABOUT 3.5 L OF OIL
SYNTHETIC TRANS OIL IS MORE EXPENSIVE BUT IT WORKS ALOT BETTER THAN STANDARD OIL

Sep 10, 2009 | 2001 Hyundai Accent

3 Answers

Oil Pan Gasket Replacement - How to - GMC Yukon 2000


No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 27, 2009 | 2000 GMC Yukon

1 Answer

Transmission fluid change


More than likely, like most automatic transmissions, yours does not have an oil plug. You need to drop the transmission oil pan to drain the old oil... You need to buy a transmission filter/pan gasket kit. The filter is located on the bottom of the tranny. You will see it when you remove the pan. Replace the filter, thoroughly remove any traces of old gasket material, clean the mating surfaces, and reinstall the pan with the new gasket. Torque the pan bolts to the manufacturers spec (you should be able to get this where you buy the filter/gasket kit). Refill the transmission through the dipstick (Capacity for the Voyager is 4 quarts, make sure to use ATF Plus (Type 7176) for your particular tranny, NOT Dexron, Mercon, or generic automatic transmission fluid, Chrysler transmissions do not like any other kind and tend to fail quite quickly with the wrong fluid). Fill to the full cold level. Start the engine, move the shifter through all gear ranges, and put it back in park. Leave the engine running and refill to cold full. Drive the car for 5-10 minutes and, with the engine still running and the car in park, fill to Hot full. You should be ready to go!

Aug 26, 2008 | 1997 Chrysler Town & Country

Not finding what you are looking for?
2000 GMC Sonoma Extended Cab Logo

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...