Question about 1995 Mercury Villager

1 Answer

Location of the engine diagnostic connector 1995 village mercury

Where can I find the location of the engine diagnostic connector on a 1995 mercury villager?

Posted by on

  • Anonymous Mar 15, 2014

    99 mercury villager install engine

  • Anonymous Mar 17, 2014

    mercury villager engine diagram

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 70,347 Answers

The diagnostic connector is located on the engine near the starter. However, there are four connectors in that location and without pictures it would be difficult to determine which is the proper one

Posted on Mar 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft pisition sensor for 1995 mercury villager


1995 Mercury Truck Villager Van 3.0L EFI SOHC 6cyl

The Crankshaft Position Sensor is located: Under hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block.

Jul 22, 2015 | Mercury Cars & Trucks

1 Answer

I had my 1995 mercury villager worcked on and now the cruse controll wont work,the light comes on but when you push the buttons on the streen whell the light on the dash it just blenks but wont kick in...


check for clean connection at vehicle speed sesnor on top rear of trans. 2 pin connector.
does speedo and odometer work?

yahoo group for villager quest owners

Jul 16, 2011 | 1995 Mercury Villager

1 Answer

Where is the OBD terminal on a 95 sable?


The 1995 Sable uses the old OBD l PCM (powertrain control module). It is located under the dash behind the glove compartment. If you are removing the PCM the electrical connector is on the firewall inside the engine compartment. There is a small bolt in the connector that you loosen as the connector is being pulled out. If you are looking for the diagnostic connectors, they are on the passenger side near the firewall, in the engine compartment.

Jan 09, 2010 | 1995 Mercury Sable

1 Answer

I have a 1995 Mercury Villager. Replaced the engine and tranny.


sounds like you bought a bad tranny,was it a used 1 you bought?

Jun 19, 2009 | 1995 Mercury Villager

1 Answer

Location of computor on 1995 merc villager


behind glove box

They seldom go bad so don't change until you know for sure. What are symptoms?

for villager/quest help go here

http://autos.groups.yahoo.com/group/villagerquest/
Powertrain Control Module (PCM) stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Refer to Module Servicing Precautions in Section 18-01 .
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the four console compartment plastic screws or C/D changer cover plastic screws (if equipped) and the console compartment door (045G36) or C/D changer cover.
  1. Remove the plastic screw, two lower screws, two center bolts, two upper screws and the screw at the instrument panel bracket, then separate the glove compartment from the instrument panel (04320). Disconnect the glove compartment striker plate catch electrical connector.
  2. Remove the two passenger side air bag module bracket nuts, the passenger side air bag module bracket bolt and the passenger side air bag module bracket.

  1. Remove the powertrain control module (PCM) electrical connector bolt. Pull the connector from the PCM and position aside.




    Remove the two PCM bolts.

    ec13884.gif

  2. Remove the PCM relay.

  3. Remove the three electrical connectors attached to the PCM.
  4. Remove the PCM from the instrument panel.

Mar 14, 2009 | 1995 Mercury Villager

1 Answer

Wire diagram for engine controls


I LIKE TO FIND WHERE TO CONNECT THE COMPUTER FOR
DIAGNOSTIC PURPOSE . I HAVE 1995 MERCURY VILLAGER

Jul 22, 2008 | 2002 Mercury Villager

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

735 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...