Question about 1994 Saturn Sl

1 Answer

Turn signals/hazards left turn signal was faster than right one. Now, turn signals and hazards don't work at all. I replaced all fuses and the fuse relay switch but they still don't work

Posted by on

  • Anonymous May 17, 2009

    I have the same problem left signal is faster than right one but also my dash lightsd are not working but hazzards do.

  • Anonymous Mar 29, 2014

    dashlightds not working after replacing turn signal switch

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saturn Master
  • 14,036 Answers

Replace turn signal switch.

Posted on Apr 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Park Avenue my turn signals do not work my flashers work


gmlogoflat.gifService Information
2002 Buick Park Avenue ' Park Avenue (VIN C) Service Manual ' Body and Accessories ' Lighting Systems ' Description and Operation ' Document ID: 643323


Turn Signal/Cornering Lamps
The HZDT/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal/hazard flasher module and have ground at G202. The turn signal lamps may only be activated with the ignition switch in the ON or ACCY position. The T/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, current flow is from the turn signal switch assembly to the turn signal/hazard flasher module. The turn signal/hazard flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators. The left turn signals have ground at G106, G400 and at G402. The right turn signals have ground at G105 and G400. The turn signal switch supplies battery positive voltage to the cornering lamps, the left cornering lamp has ground at G105 and the right cornering lamp has ground at G106.
+snpvvsvwho06+5aqhepgaaaabjru5erkjggg==










2002 Buick Park Avenue ' Park Avenue (VIN C) Service Manual ' Body and Accessories ' Lighting Systems ' Description and Operation ' Document ID: 643323

May 10, 2016 | Cars & Trucks

1 Answer

The fuse for a right turn signal on a 2001 Buick Park Avenue


The left an right turn signals get there power from same fuse ,HZDT/SG fuse 15amp in the left under hood fuse box. through the turn signal hazard flasher module. Here is how they work .
Turn Signal/Cornering Lamps
The HZDT/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal/hazard flasher module and have ground at G202. The turn signal lamps may only be activated with the ignition switch in the ON or ACCY position. The T/SIG fuse in the fuse block - underhood - left supplies battery positive voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, current flow is from the turn signal switch assembly to the turn signal/hazard flasher module. The turn signal/hazard flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators. The left turn signals have ground at G106, G400 and at G402. The right turn signals have ground at G105 and G400. The turn signal switch supplies battery positive voltage to the cornering lamps, the left cornering lamp has ground at G105 and the right cornering lamp has ground at G106.The turn signal switch or the turn / hazard flasher module is bad or there is a wiring problem. Go to you tube an check out a few videos on basic electrical testing ,then get a DVOM - digital volt ohm meter , an wiring diagram an trouble shoot the circuit . There may even be a video on test turn signal circuit .

Dec 04, 2015 | Buick Cars & Trucks

4 Answers

Turn signal lights don't work


The first place to start are fuses, check your owners manual for location, typically left side of dash.

The emergency (hazard) flashers and turn signals are on separate fuses and run through the hazard switch. If all the lights work when the hazard switch is on then the problem will likely be a blown turn signal fuse.

Other possibilities are the hazard switch itself is bad, the turn signal switch is bad or a broken wire, all of which require a meter (or test light) wiring diagram and knowledge of the circuit to test it - better to have it done.

Robert Grove
Mobile Mechanic Malibu 310 651 8020 Auto Truck RV Mobile Repair...

Aug 09, 2014 | 2002 Chevrolet Impala

1 Answer

2010 chevy equinox right rear turn signal doesnt work, replaced bulb and still the same. front works, is there a fuse for the rear light and where is the fuse located.


RT/SIG fuse #11 15amp - I/P fuse box . Fuse Block - I/P
In the center of the instrument panel, beneath the right side of the radio, in back of the right side console access panel.
This fuse is power to the BCM , When you put on the right turn signal , this is a voltage signal to the BCM . With logic ( programming ) the BCM then controls the turn signal !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
There could be a DTC- diagnostic trouble code stored in the BCM pointing to the problem ! I suggest you take your vehicle to the dealer or a ASE certified repair shop that has the diagnostic tools to find the problem . Just so you don't waste your money replacing parts that don't fix it.
There could

Dec 14, 2012 | 2005 Chevrolet Equinox

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

2008 Entourage right turn signal blinks 2x faster. Does this mean i need to replace fuse? Where is fuse located?


you might have a blown bulb. turn on 4 way flashers (hazard lamps), walk around vehicle and see which one is not working. Replace burned lamp.

Aug 07, 2012 | 2007 Hyundai Entourage Limited Minivan

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...