Question about 1999 Jeep Grand Cherokee

1 Answer

Installing driving lights on my non-driving light 1999 Jeep

I have bought and installed everything to have driving lights on my 99 JGC which did not come with driving lights and I'm afraid I've reached a dead end. It calls for a relay switch and a fuse but where the relay and fuse should go there is no plugs in the fuse boxes. Anyone have this problem?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

Here is what you need to get. You need to buy a 30 amp circuit breaker. Tap your power supply and install the two terminal 30 map breaker in to the power wire. This will protect your switch if the wire should short out for some reason. One side of the hot line goes to the switch. The other side of the switch needs a wire going to the lights that share a common power supply line. The two lines that are your ground lines from the lights will link together and ground them to the metal body or frame somewhere. Then you are good to go. You should be able to purchase a 30 amp ciecuit breaker at just about any parts supplier cheaply. They are very small and made out of tin on the outside. It should not cost you over $ 5.00 to purchase. Good luck.

Posted on Mar 08, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1999 jeep grand cherokee tacometer reading???

Cruising rpm even after the OD has engaged has a lot to do with the differential gear ratio and tire size.
There will always be a variation between different vehichles due to that alone.
To see if the OD is working, at about 50mph, lightly touch the brake pedal. If the rpms increase for a moment then the OD was engaged. (touching the pedal momentarily disengages it...good thing to know when hill climbing!

Apr 27, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Just replaced the tps in my 99 JGC and it still runs the same as

first check for a vacuum leak.if none,check air idle controle for not working or carbon build up that will sometimes make the pindel stick,also dodges have a valley pan bolted on under side of the intake those gaskets can leak and cause very wierd vacuum problems on the crank case. hope i was some help.

Jul 04, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1998 JGC Quadra Drive problems

Is there any oil in it? Sounds like your valves were sticking until it completely fried everything.

Jun 17, 2009 | 1998 Jeep Grand Cherokee

1 Answer

99 JGC stuck in Part Time 4WD

always put it in and take it out when you are moving in a straight line. its very important also that all 4 tires are approx the same diameter otherwise it will stick as you say yours does

Sep 09, 2017 | 1999 Jeep Grand Cherokee

2 Answers

Check engine light on and clunking going into first gear not going to second

Your syncros are going out. Try matching revs and you might get it into each gear okay, but get them checked. They'll be in the top of the tranny.

Oct 21, 2008 | 1999 Jeep Grand Cherokee

1 Answer

Transmission won't shift out of 1st gear

the output spped sensor is on the drivers side rear of the transmission case..its a 2 wire connector..the wires are dark bluewith a black tracer and light green with a white tracer

Sep 30, 2008 | 1999 Jeep Grand Cherokee

1 Answer


I had the same problem with my 99 jeep. Turns out the turn signals, hazard lights and brake lights are part of the turn signal switch. I replaced mine and everything worked great.

Aug 08, 2008 | 1999 Jeep Wrangler

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides