Looking at the opened door from the inside remove the philips screw near the upper hinge. Pry the speaker grill off with a thin blade putty knife, starting at the bottom left and work to the right. Remove speaker screws and the three screws in the recessed plastic spaces behind. Remove the square covers behind the handle and in the arm rest. Remove the 2 philips screws exposed. Start to pry from the top hinge side between the plastic door panel and the metal door. Work your way around the door until plastic clips release. Once the bottom of the panel and sides are free, lift the panel up and off the door being careful not to pull wiring and door handle mechanism loose. Unplug the as much of the wiring as you can and support the panel so as to not stretch the wiring. Pop the plastic retaining clip on the door handle connecting rod and lift the rod out of the handle. Slowly peel back the vinyl/rubber door cover stuck to the metal door. The window is held in the lower track with two clips that are bolted to the track. Unbolt by raising or lowering the window and using a 10MM socket on the nuts to loosen. Remove the window seal along trhe bottom of the window opening by prying straight up. You can then remove the window and re-epoxy in the lower clips and reassemble window in reverse order.
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
On a 98 Plymouth Breeze, I think you access the battery from one of the front wheel wells because it's located under one of the fenders. I'm not sure which side it's on, but you should be able to get to it by turning your wheels all the way in one direction.
The AC Clutch is going and is slipping, thus the swishing sound..sorry. When the Defrost or AC is turned on the Clutch is Engaged. And yes the AC Unit replacement is recommended over trying to have the Clutch replaced. Most mechanics won't even try rebuilding an AC Unit.
probably need a new window regulator. ebay. 93 to 98 should fit.
Section 01-05: Trim, Interior
1998 Villager Workshop Manual
REMOVAL AND INSTALLATION
Trim Panel(s), Door
Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
Pull the shop rag back and forth to release the window regulator handle clip.
Remove the three cover caps and front door trim panel screws.
Remove the one front door trim panel capped screws from the door pull handle.
If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
Remove the front door trim panel.
To install, reverse the removal procedure.
Window Regulator, Power
Front Door Removal
Disconnect the battery ground cable (14301) .
Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
Remove the two front door brace bolts and the front door brace.
Disconnect the front window regulator electric drive electrical connector.
Remove the four front door window glass regulator track bolts.
Remove the three front window regulator electric drive bolts.
Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
On the inside trim, you can remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. You'll need to lift the door panel upwards in order to
get it off the window ledge. Then you'll need to manipulate the panel
and disconnect the door handle linkage from the door handle and
disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
One of three spots. First, right behind the gas tank. Second, -IN- the gas tank (have a proffesional do it if that's the case, you'll save yourself money in extra repairs and alot of headache), and third is on the driver side frame near front door.