Question about 2003 Pontiac Montana

1 Answer

How do i remove the battery? - 2003 Pontiac Montana

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 214 Answers

Hmmm.. Remove fender Brace.. coolant tank, cruise control Module.. Then its easy

Posted on Mar 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove battery


  1. If equipped with power seats, move the seat to the most forward and upright position.
  2. If equipped with manual seats, move the seat to the most forward position.
  3. Turn the ignition switch to the Off position. Be certain that all electrical accessories are turned off.
  4. Remove the battery cover (1).
  5. Remove the negative battery cable (1) from the battery.
  6. Disconnect the positive battery cable and position aside.
  7. Remove battery thermal blanket.
    1. Remove the battery hold down retainers (2) and remove the battery hold down (1).
    WARNING: Wear a suitable pair of rubber gloves when removing a battery by hand. Safety glasses should also be worn. If the battery is cracked or leaking, the electrolyte can burn the skin and eyes.
    1. Remove the battery from the vehicle.

Jul 12, 2013 | 2012 Jeep Grand Cherokee

1 Answer

How to remove starter motor


REMOVAL
1. Disconnect battery terminals
2. Remove bolt and battery clamp
3. Remove battery
4. Clean battery tray
5. If equipped with cruise control, disconnect multiplug and hose from cruise control vacuum pump.
6. Release harness clips from battery carrier
7. Remove 4 bolts and remove battery carrier.
8. Remove battery carrier and cruise control vacuum pump (if equipped).
9. Release starter motor solenoid terminal cover.
10. Remove nut securing battery lead to solenoid and disconnect battery lead
11. Disconnect Lucar connector from starter solenoid.
12. Remove 3 bolts securing starter motor to gear box. Note that the left hand bolt also secures the mounting bracket for the Crankshaft Position (CKP) sensor multiplug.
13. Maneuver and remove starter motor from vehicle.
INSTALLATION
1. Clean the starter motor mating face on the gear box.
2. Install the starter motor by reversing the procedure in the removal instructions.
3. Before connecting the battery, clean the cable terminals and the battery posts.
4. Apply a thin coat of petroleum jelly or dielectric grese to battery terminals after connecting.

Dec 14, 2011 | 2002 Land Rover Freelander

1 Answer

Replace battery


Remove the negative cable end from the battery. Remove the positive cable end from the battery. Remove the hold down bolt from the front of the battery hold down. Loosen the rear battery hold down nut and remove the battery hold down. Remove the battery. Reverse this order to reinstall.

Sep 25, 2011 | 2001 Toyota Camry

1 Answer

Replacing battery on Aston Martin Vanquish


Below is the procedure for an Aston Martin Vantage, perhaps the vanquish is similar?

Removal
1. Power the driver's fully forward.
2. Remove rear compartment cover.
3. Loosen and disconnect battery terminals, earth (- ve)
terminal first.
4. Release rear carpet, studs (x2), move carpet aside.
5. Remove screws (x2), battery compartment cover to
support rail.
6. Remove nuts (x2), battery compartment cover to body.
Remove cover.
7. Remove Torx screws (x4), remove battery clamps (x2).
8. Disconnect battery vent tube.
9. With assistance, remove battery.
Installation
1. Clean battery tray and clamps.
2. With assistance, install battery into its compartment.
3. Connect battery vent tube.
4. Position battery clamps (x2), install and torque tighten
Torx screws (x4).
5. Ensure battery vent tube is not distorted by battery.
6. Install battery terminals, tighten terminal nuts to correct
torque.
7. Install battery compartment cover, install and tighten
screws (x2) and nuts (x2).
8. Position rear carpet, secure with studs.
9. Install rear compartment cover.
10. Reposition driver's seat.
Courtesy of pistonheads.com

Please vote if this helps! Thanks, Mike

Jun 12, 2011 | Aston Martin Vanquish Cars & Trucks

1 Answer

How do I remove the battery from a 2006 Dodge Durango?


One side of that battery will have a single 13 mm bolt that you can loosen and or remove entirely to allow you to remove that battery. Screws located down near the bottom of the battery.
The fender is on the left and then the battery and then the wedge is on the battery side which faces the engine. You need to remove it with a socket and long extension.

Remove the negative battery and place it out of the way then remove the positive cable and move it as well.Remove the heat guard or shield which surrounds the battery if installed.Remove the battery hold down wedge by unscrewing the bolt.Lift out the battery.Reverse for installation.--------------- Thank you.


Jan 31, 2011 | 2006 Dodge Durango

1 Answer

Trying to remove the battery from my 2007 soltice


Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .


Joe
Thanks for choosing Fixya!

Jan 30, 2011 | 2007 Pontiac Solstice Convertible

2 Answers

How do i remove a battery from a 2002 chrysler concorde


Battery is behind the front left wheel. You have to remove the wheel to replace the battery. (you can access the battery w/out removing the wheel, but you can't actually get the battery out unless you take the wheel off.)

Once the wheel is off, remove the inner-fender well mud-guard and you will see the battery just forward of the wheel well. From there it's pretty straight forward.

Once this is removed, you should be able to see the battery hold-down bolts.

Remove these and remove the hold-down assembly.
If you are removing the battery, remove the 1st battery cable.

Depending upon what battery you have, you may be able to slide the battery back toward the wheel and disconnect the 2nd cable.

Jack the vehicle up, put on jack stands and remove the passenger side wheel.

On the front side of the wheel well there is an access panel that needs to be removed in order to access the battery. There are 6-8 1/4" screws to remove. Then manipulate the cover until you can remove it, bending it slightly.
If you were unable to disconnect the 2nd battery cable earlier, you can now move the battery further towards the rear of the car. Remove the 2nd cable clamp from under the hood.

Slide the battery all the way out. It is heavy!
Reverse the instructions for reassembly.

Aug 17, 2010 | 2002 Chrysler Concorde

2 Answers

I need to replace the battery. How do I do this?


Hi!!

The battery is located in the fender, ahead of the right front tire. Te battery can be removed without reovint the tire, but removing it improves access.

Here is how to remove/replace the battery

Disconnect battery cables, negative first, then positive from remote terminals.

Remove air filter housing

Remove the two battery hold down clamp bolts and clamp.

Loosen right front tire lug nuts, rise the vehicle, support it w/jackstand and remove wheel.

Remove battery cover/splash shield from wheel well

Slide battery toward rear of vehicle and disconnect battery cables.

Remove old battery thru wheel opening and insert new one.

If helpful, click below

Apr 13, 2010 | 2003 Chrysler Concorde

2 Answers

Dead battery


Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

Oct 15, 2009 | 2006 Pontiac Solstice

1 Answer

Battery removal


The battery is located under the right front fender behind the tire. Remove the wheel, remove access panel from fender well. From engine compartment, remove 2 battery hold down bolts,10mm, slide battery rearward to remove battery cables.

Oct 18, 2008 | 2003 Chrysler Concorde

Not finding what you are looking for?
2003 Pontiac Montana Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...