Question about 1982 Ford F 250

1 Answer

C6 grinds in first - 1980 F-250 - C6 with shift kit. Was sitting all winter. Terrible grinding noise and no power. Engine doesn' t want to idle either. Thought it was the rearend. Took it apart looked ok, changed fluid..still grinding. Noticed that the grinding stopped when shift out of 1st. Is there a quick fix, maybe Lucas transmission additive.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

I would the oil level in the tranny.mabee from sitting some leaked out.But i would add the Lucas as soon as i could.

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Solenoid rattle on start up. Goes away immediately on start. V 6 motor


peugeot 407 v6 3.0 very short-time rattling(grinding) noise at ...

? 0:13
https://www.youtube.com/watch?v=ZRJzci7qvNA
Feb 27, 2012 - Uploaded by reza679
peugeot 407 v6 3.0 very short-time rattling(grinding) noise at cold-start, source ... but a friend told me it can be anything else as well (like those solenoids)! ... C6 makes when starting cold - is that a VVT or a valve lifter noise?.

407 [Archive] - Peugeot Forums

www.peugeotforums.com > Peugeot Forums > Peugeot Models
Mar 22, 2011 - Key replacement · Wishbones for 407 · ESP/ASR Faulty · RT4 VIN coding · 407 1.6 2004, Crankshaft pulley.. size, part number.. 407 driver door lock replacement ... Peugeotforums.com Suggestions and Help [Archive ...
Mar 24, 2011
General Discussion [Archive] - Page 4
Mar 21, 2011
More results from www.peugeotforums.com

Jan 26, 2016 | 2006 Peugeot 407 1.6

1 Answer

Ford f250 1989 diesel c6 transmission Loud unregular noise, not driving, running idle, shift and drive normal. Sounds like parts loose in gearbox.


See if it the torque converter making the noise. Ford had these converters take would make like a rattle/clicking noise. Not sure if they went back that far though. The noise doesn't hurt anything. Every thing still works fine. It was just annoying.

Jul 04, 2015 | Cars & Trucks

1 Answer

1989 Ford F 150 lariat 4x4 pick up pops out of reverse and makes a terrible grinding noise until it's put back in noise is coming from transfer case fluids have been checked and changed no shavings also...


You must have a manual transmission. Rebuild it. synchronizers are bad. The reason for grinding. Then you have worn shift forks. Reason for popping out of gear. Also replace any worn bearings or just get the bearing kit and replace them all, with the races.

Sep 30, 2014 | 1989 Ford F 150

2 Answers

1988 ford F-250 i have to accelerate hard to make it shift into 3rd gear but as soon as I let off gasd it goes back to 2nd.i changed fluid and filter.wondering if it is modulator valve.


Ford C6
Verify there is vacuum to modulator, the rubber line tends to break/falloff
Verify the kick-down cable is correct
Verify the linkage is correctly adjusted.
A C6 reads engine vacuum and throttle position to automatically shift

Oct 14, 2009 | 1988 Ford F 250

1 Answer

Ford c6 transmission not shifting???


you may have a block trans air vent which may explain the blown seal and may also fect shifting

Sep 09, 2009 | Ford Econoline Cars & Trucks

1 Answer

Will a ford c6 tranny bolt on to a 1995 ford 5.0l or 5.8l motor?


From 1990-1996 The C6 was replaced by the E4OD which was modified to include a fourth forward speed and electronic shift controls, replacing the hydraulic control mechanism of the C6.

The C6 works fine in your bronco.. Your friend will need a different transfer case!. i dont have the manual but this is my best guess. FOrd likes to make cars that have interchangeable parts. Like a 1999focus can interchange with 2007. as long as the liter and engine size are the same. In some cases. you will have to use different transfercase.

So you might be better off with a c6 transfer case or c4 for your friend.

Hope this helps

Feb 16, 2009 | 1995 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...