Question about 1994 Mazda 323

Open Question

Front camber adjustment Mazda 323 Astina 1997

Would be great if someone could tell me how to do the camber adjustment on this car myself. I suspect the 17 mm bolt on the lower control arm is the adjusting bolt...is it locket by a nut or do i just turn it to get the adjustment? If there is a nut on the end of this bolt it's impossible to get to without dissmantling other parts of the car.

Posted by on

  • Devon Sacco
    Devon Sacco May 11, 2010

    It's hard to explain over the computer.

    My advise is to buy a do-it-yourself book (like hayes or chilton) at a auto parts store, so you can see the pictures of where the adjustment nuts are located.

    BD

×

5 Suggested Answers

Service Dude
  • 201 Answers

SOURCE: 1989 mazda astina 323 5 spd manual clutch fluid??

open your bonnet check to see @ gearbox if the-res is cable, or a cylinder, the cable is Usualy visible on the top of the gearbox if theres a cable theres no clutch flu-ed needed. Note that your gearbox uses oil. Usualy on older models like 1989 the use a clutch cable no flu-ed needed

Posted on Jan 03, 2009

  • 218 Answers

SOURCE: Battery for 1997 Mazda 323 Astina 5dr hatch

It's fine to use a battery with a higher cold crank rating than original. Consider the rating in the manual to be a minimum requirement. You'll be fine as long as the physical dimensions and terminal placement are compatible with your car. The battery manufacturer's guide should tell you which battery fits your car.

Posted on Mar 03, 2009

jturcotte
  • 6812 Answers

SOURCE: can u tell me please where to locate fuel pump

It may be the circuit relay #21 in the battery junction box. See diagram below. Let me know if you have more questions.


jturcotte_89.gifjturcotte_90.gif

Posted on Nov 07, 2010

emissionwiz
  • 61249 Answers

SOURCE: 2000 model mazda 323 astina cylinder head bolt torque specs

Three stages with new bolts (a must), 1st 60 pounds, then 70 pounds then final torque is 80 FT Pounds.

Posted on Feb 16, 2012

  • 141 Answers

SOURCE: mazda v6 timing marks astina 1994

There should be little groves on the crank pully 4 or 5 marks

Posted on Nov 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot find spark plugs in 2003 323 1.8 litre mazda astina


If you follow the wires to the top of the engine from the distributor, they are under the boots when you remove them. Plugs are about 4-6" down inside. f2c5d262-e131-42d7-8496-0946d38b78c6.jpg

Apr 20, 2014 | 2003 Mazda 323

1 Answer

Mazda v6 timing marks astina 1994


There should be little groves on the crank pully 4 or 5 marks

Nov 09, 2013 | 1989 Mazda 323

3 Answers

Mazda 323 park brake light won't turn off


Theres a little switch that activates the light. It could possibly be sticking

Mar 18, 2013 | Mazda 323 Cars & Trucks

1 Answer

My 1994 mazda 323 astina automatic revvs high and low. what's the problem


When does is rev high and low? If it does this at idle check for a vacuum leak or maybe a blocked airflow

Jan 12, 2013 | 1994 Mazda 323

1 Answer

2000 model mazda 323 astina cylinder head bolt torque specs


Three stages with new bolts (a must), 1st 60 pounds, then 70 pounds then final torque is 80 FT Pounds.

Feb 16, 2012 | Mazda 323 Cars & Trucks

2 Answers

Can u tell me please where to locate fuel pump relay mazda astina 323 1997


It may be the circuit relay #21 in the battery junction box. See diagram below. Let me know if you have more questions.


jturcotte_89.gifjturcotte_90.gif

Nov 07, 2010 | 1994 Mazda 323

1 Answer

Front camber adjustment Mazda 323 Astina 1997


their is no camber adjustment,its factory preset so to speak by virtue of its design.If you are having a`problem with tyre wear on this side then first measure outside wheel rim front to back wheel through centre ,both sides and see if distance is more that half a centimetre,look at distance between back of wheel and wing if its not equal each side of car then you have a problem.if its just a bit of scuffing on outside of tyre then this is normal and its caused by the power steering.If the wheel is not within the same distance either side then its either a body jig to straighten or the lower track control arm bent ,this sort of thing is caused by people drinking and driving or using a mobile phone whilst driving ,and wacking the kerb.Or evan worse women drivers trying to reverse park with wheel on lock and trying to mount pavement.

Mar 08, 2009 | 2006 Lexus RX400h Used Cars

1 Answer

Battery for 1997 Mazda 323 Astina 5dr hatch


It's fine to use a battery with a higher cold crank rating than original. Consider the rating in the manual to be a minimum requirement. You'll be fine as long as the physical dimensions and terminal placement are compatible with your car. The battery manufacturer's guide should tell you which battery fits your car.

Mar 03, 2009 | 1994 Mazda 323

1 Answer

Gears sticky when changing, sometimes crunchy even?


It looks incorrect clutch adjustment, first inside the car depress the clutch pedal by hand and see if there is a free play moor then 10 mm, if so , slacken the locknut at the cable end in engine compartment, now turn the adjustment nut until the distance from the release lever to the roller on the cable is about 3mm, tighten the locknut after adjustmen

Jan 13, 2009 | 1988 Mazda 323 Hatchback

Not finding what you are looking for?
1994 Mazda 323 Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...