Question about 2001 Dodge Intrepid

1 Answer

2001 Intrepid, is the tie rod end located above the wheel and is it a threaded assembly?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

The tie rod end is at the wheel their is an outer and a inner they are both threaded

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car shekes when hit bumps


Check for bad wheel balance, struts, lower ball joints ( no upper joints) , outer tie rod ends, inner tie rod ends, stabilizer bar bushings, lower control arm bushings , and finally a wheel alignment ,you have some bad looseness in one or more of these front end parts. GOOD LUCK FRIEND.

Mar 15, 2015 | 2001 Dodge Intrepid

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

HOW TO REPLACE BENT TIE ROD


if its the outer tie rod then you can loosen the lock nut on threaded portion that attaches to the inner tie rod then remove the nut that locks the tie rod to the spindle assembly.you can hit the area were the tie rod stud goes through the hole to loosen it to remove it from the assembly.then count the number of turns to remove it from the inner tie rod end.then install the new one the number of turns you took the old one off and reassemble in reverse order.its a good idea to get the alignment done to make sure the wheels are positioned right and not wear the tires out early.

Nov 01, 2011 | 2002 Dodge Grand Caravan

2 Answers

Replace the tie rod on a 1998 sienna


1 PUT ON YOUR EMERGENCY BREAK, LOOSEN THE WHEEL NUTS ON THE FRONT WHEELS,JACK UP THE CAR AND REMOVE THE FRONT WHEEL. WITH SOME YELLOW PAINT ,MARK THE THREADS WHERE IT SCREWS INTO THE TIE ROD END SO YOU KNOW HOW FAR TO SCREW THE NEW ON ONTO. TAKE OUT THE COTTER PIN AND REMOVE THE CASTLE NUT FROM THE ROD. USE A PRY BAR TO SEPERATE THE BOLT FROM THE TIE ROD END. ONCE SEPARATED YOU SHOULD BE ABLE UNSCREW THE OLD TIE ROD END OFF THE SHAFT..TAKE THE NEW ONE AND SCREW IT BACK ON ONLY TO THE YELLOW PAINT MARK THAT YOU MADE ON THE ROD EARLIER. THEN JUST REASSEMBLE THE SAME WAY YOU TOOK IT APART. MAKE SURE YOU TORQUE THE NUT TO 50 LBS.AND BE SURE TO USE A NEW COTTER PIN ON THE CASTLE NUT..

May 04, 2011 | 1998 Toyota Sienna

1 Answer

How to replace the tie rod end


Tie rod ends are replaceable, whether the steering system is rack and pinion or parallelogram steering system.
f42-02.gif Parallelogram steering system mounts. Figure A - behind front suspension; and Figure B - ahead of front suspension. f42-04.gif A rack and pinion steering system. Tie rod ends are threaded to provide a means of adjusting toe. When a tie rod is replaced, measure the old tie rod assembly before disassembling it. An approximate toe-in adjustment can be made to the new one prior to installation. When removing the old tie rod end, count the number of turns it takes to remove it. Then, turn the new tie rod end onto its threads the same number of turns.
Some vehicles have tie rods that appear to be the same on both ends. The difference is in the threads. One end has left hand threads and the other has right hand threads. It is possible to install the entire shaft backwards (which will work). Mark the tie rod to identify the inner or ourter end before removing it.
Before tightening tie rod clamps, check to see that they are in good condition and are positioned properly so they can be clamped tightly. Before doing a front end adjustment, spray penetrating oil on the threads of the tie rods. Do this during the steering linkage inspection so the lubricant has time to soak in.

Nov 12, 2010 | 2002 Dodge Stratus

1 Answer

Is a special tool required to remove inner tie rod from relay rod on 2001 Tahoe.? Also what should torque be?


Relay Rod Removal & Installation To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Engine protection shield, if equipped
    • Steering damper from the relay rod, if equipped Note: Use the proper tool in order to separate all the tie rods and the ball joints.
      Steering components gm_trk_sub15_steering_components.gif

    • Tie rod ends (F) (See: Tie Rod Ends)
    • Idler arm ball stud nut (J) and discard the nut (See: Idler Arm)
    • Pitman arm nut (H) and discard the nut (See: Pitman Arm) Remove the idler arm from the relay rod gm_trk_sub15_idler_from_relay_rod.gif

    • Relay rod from the idler arm ball stud using the J24319-B or other suitable puller Remove relay rod from pitman arm ball stud gm_trk_sub15_relay_rod_rem.gif

    • Relay rod from the pitman arm ball stud using the J24319-B or other suitable puller
    • Relay rod from the vehicle
  3. Inspect the threads on the tie rod ends for damage
  4. Inspect the ball stud threads for damage
  5. Inspect the ball stud seals for excessive damage
  6. Clean the threads on the ball studs
To Install:
  1. Install or connect the following:
    • Relay rod to the vehicle
    • Relay rod to the pitman arm ball stud
    • Relay rod to the idler arm ball stud and make sure the seal is on the stud
    • New pitman arm prevailing torque nut
    • New idler arm prevailing torque nut and tighten the idler arm and pitman arm nuts; Torque to: 46 ft. lbs. (62 Nm)
    • Tie rod ends
    • Steering dampener to the relay rod, if equipped
    • Engine protection shield, if equipped
  2. Lower the vehicle
  3. Check the wheel alignment
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Sep 18, 2010 | 2001 Chevrolet Tahoe

1 Answer

TYROD


to change a tierod on 2001 malibu, jackup and remove front tire, next locate the nut holding tierod on tire side, remove cotter pin and loosen but do not remove the castle nut from the tie-rod end ball joint stud. then install a small puller and break loose the tie-rod end from the steering knuckle. remove nut and detach tie-rod end. (I forgot to mention before taking tie-rod end off of vehicle,loosen the tie-rod end jam nut and mark the position of the tie-rod end on the threaded portion of the tie-rod. you can also count the number of turns to take off so you can put it back on.) make sure the new tie-rod end is aligned with the mark you made on the threads of the tie-rod. have the alignment checked or adjusted after you have installed tie-rod end. if in doubt you can go to any auto parts store and buy a haynes manual for your vehicle, they are based on a complete vehicle teardown. the cost is only about 20.00.

Nov 23, 2009 | 2001 Chevrolet Malibu

1 Answer

Rack pinions and bushing installement


pretty decent job ahead first jack up car support with jack stands remove front wheels remove nuts on tie rod ends remove tie rod ends from spindles with tie rod end tool or tap with malet were they sit to loosen them hit the spindle area not the tie rod or tie rod threads then dissconnect power steering lines from steering rack also disconect steering linkage to rack there should be 2 main bolts holding assembly to frame remove them should free rack i know that car may have a unique design were u may have to remove inner tie rod ends first if it has those round bushings that always go bad disconect inner tie rod ends behind engine on top of steering rack then remove rack from wheel well replace those inner tie rod bushings u may be able to leave outer tie rod end connected to spindles and u may be able to get to the sterring rack from behind engine good luck

Mar 28, 2009 | 1997 Chrysler Concorde

2 Answers

1997 dodge Intrepid: inner tie rod


To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
NUMBER: 19-001-01
GROUP: Steering
DATE: Mar. 23, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

SUBJECT:
Loose Steering

OVERVIEW:
This bulletin provides service procedures and parts information for the inner tie rod bushings.
MODELS:
1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
SYMPTOM/CONDITION:
Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
DIAGNOSIS:
Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
DISCUSSION:
The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

Jan 13, 2009 | 1994 Dodge Intrepid

1 Answer

Car shakes through the brakes and steering


Well, just because the rotors are new doesn't mean they are nor warped, do you feel the vibration in the steering wheel or in your seat? The other thing about Intrepeds is the inner TIE ROD ENDS very common, While your there check lower ball joints and outer Tie Rod Ends, have someone look at the tie rod ends located behind the engine while someone turns the steering wheel left and right in short quick strokes if you see loosness there you have to fix that problem.
If you feel the virbration in your seat the rear rotors are your culprit also make sure whoever does the brakes to clean and service the caliper guide pins make sure they are clean and lubed with lilicone grease made for that porpous and grease all points where the pads ride on the mounts.
Please contact me if you need more help and would you please leave me a favorable rating? Thank you, Randy

Aug 10, 2008 | 2004 Dodge Intrepid

Not finding what you are looking for?
2001 Dodge Intrepid Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...