Question about 2000 Ford Escort

1 Answer

Turned ignition on, nothing. no engine. lights & indicators working, but no engine. any suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Main fuse, EFI relay possibly. What model is your car?

Posted on Mar 08, 2009

  • Metal Unlord
    Metal Unlord Mar 10, 2009

    OR flat battery, immobiliser, or starter motor.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuses ok,light in dash tested and works. But check engine light does not come on when you turn on the ignition. What else should I check? This is a ford ranger XLT 4x4 4.0L V6-245cid engine (pushrod)


The instrument cluster (10849) carries out a display proveout to verify that all warning/indicator lamps and monitored systems are functioning correctly. When the ignition switch (11572) is in the ON position with the engine (6007) off, the following indicators will illuminate:
  • CHECK ENGINE/malfunction indicator lamp (MIL).
  • CHECK GAGE warning indicator.
  • Charge system warning indicator.
  • Anti-lock brake warning indicator (ABS).
  • Safety belt warning indicator (60second proveout).
  • Air bag indicator.
  • An indicator is inoperative - CHECK ENGINE/malfunction indicator lamp (MIL)
  • Bulb.
  • Circuitry.
  • Instrument cluster printed circuit.
  • Powertrain control module (PCM) (12A650).
  • GO to Pinpoint Test N .

Feb 15, 2016 | Cars & Trucks

1 Answer

Remotekey will not work. dashboard indication not lit.only powere steering light no clock or temperature lit. all fuses ok


A fuse can blow but physically look intact. How did you verify the fuses were ok? It could be that the 40A fuse 8 in the engine compartment fuse box has blown.
This supplies multiple circuits which are themselves individually fused in the consumer box inside the car.
The smaller 15A fuse 15 in the consumer box would normally blow under these circumstances but f the horn does not work as well and there are other things you have not listed that do not work like brake lights or headlights, it is definitely the under bonnet fusebox where the problem lies.
Good luck.

Jul 28, 2014 | 2007 Suzuki Swift 1.3

1 Answer

Ignition problem on 1995 525i bmw


Sounds like a flat battery ... Charge it or replace it

May 05, 2014 | 1995 BMW 5 Series

1 Answer

I have a 2002 cadillac seville northstar engine. When I turn key lights come on dashboard but does not turn over. It does nothing. I changed the starter and still nothing. Any suggestions?


see the commentary and diagram attached.God bless you

When you turn the ignition ON before starting the car, the "Check engine" light is supposed to come on indicating that the engine computer (also could be called ECM, PCM, or ECU) is powered on. If the "Check engine" light does not come with the ignition ON, it's possible that there is no power coming to the engine computer (e.g., due to a broken wire, faulty main relay, burnt fuse, etc.) or that there is a problem with the engine computer itself.
1c69a59a-f5b7-42c5-be71-d37ac428a353.jpgRun the scanner/computer for easy diagnostic and fix it.b7a81555-a639-4e34-ad3c-b6e597f477da.gif

Jul 27, 2013 | Cars & Trucks

1 Answer

My maintenance light is still on even though i have changed my engine at 60,000 mileage, what could be the problem and how can i make it stop (toyota corolla 06)


To reset Maintenance light, do the following procedure:

  1. Turn the ignition to run (one position before starting engine).
  2. Ensure odometer reading is shown. Turn ignition off.
  3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
  4. Hold down knob for at least 5 seconds. The odometer indicates "000000" and the light goes off. If the system fails to reset, the light will continue flashing.
  5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Apr 13, 2012 | 2006 Toyota Corolla

1 Answer

Won't start. Turn the ignition and nothing. The engine light comes on and the auto theft light comes on for a few moments and goes off. I tried the couple things suggested in the owners' manual...


if nothing happens when you turn the key the problem is most likely the ignition switch and housing(had mine replaced 3 times already. firstr time at 12,000 miles) what you can try is hit key with rubber mallet while trying to turn but this would only be to get it started so you can drive to a chevy dealer(dont waste your time at any old repair shop for this). Hope this helps.

Aug 11, 2011 | 2008 Chevrolet Cobalt

1 Answer

Long beep after ignition


Beep indicates a problem, can mean many things like engine fault, or low washer fluid, or turn signal bulb is out. If nothing shows up on the dashboard, check your turn signals, brake lights, and head lights

Nov 10, 2009 | 2004 Infiniti FX35

1 Answer

Engine will not turn over or make much of a sound.


It sounds like it is probably your ignition switch. Either that or your starter selenoid.

Jun 19, 2009 | Volkswagen Beetle Cars & Trucks

1 Answer

1999 Pontiac Grand Prix lights are staying on


what is the procedure you are using can you explain it to me?
Resetting Procedure

To reset the CHANGE OIL SOON indicator if equipped with the Driver Information Center (DIC).

  1. Turn the ignition to ON without starting the engine.
  2. Fully press and release the accelerator pedal three times within five seconds.
    • If the CHANGE OIL SOON indicator flashes two times, the system is resetting. Turn the ignition key to OFF then start the vehicle.
    • If the CHANGE OIL SOON indicator comes on and stays on, repeat the procedure.
To reset the OIL LIFE indicator if equipped with a Trip Computer.

  1. Press the trip MODE button until the light appears next to OIL LIFE.
  2. Press and hold the trip RESET button until the oil life percentage changes to 100%.
Hope this helps Ill look into the ABS lights but I do believe that you will need a scan tool to retreive a code to be able to diagnose the reason for the lights



Sep 18, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
2000 Ford Escort Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...