Question about 1993 GMC G2500

1 Answer

How to replace hub bearing? - 1993 GMC G2500

Posted by on

  • Tommy Moore
    Tommy Moore May 11, 2010

    First of all.. is it 4 wheel drive??

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try “autozone.com” or your local library for diagrams and step by step instructions and here is a place for the parts if needed: Schram auto and truck parts 1-800-292-1032 they sell only GM parts

Posted on Mar 08, 2009

2 Suggested Answers

  • 186 Answers

SOURCE: NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING

Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

Posted on May 19, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I replace rear wheel bearings only on my 2007 sorento [I realise I need to have them pressed in] or do I need to replace whole hub & bearing assembly its a solid axle type


Hub bearings are always replaceable using the existing hub. You only need to press them in by hand and then tap them in with a socket big enough to sit on the outer bearing race. Put the hub on the car, put the tire on the hub and tighten the hub nut whilst turning the wheel until the pressure on the bearing caused the wheel to lock up. Then back the bearing off by the required amount, usually a quarter turn. Check the manual.

Nov 24, 2015 | 2007 Kia Sorento 4x4

1 Answer

How do you remove a rear hub on a 04 kia sedona?


Call Kia with your VIN to make sure yours wasn't affected by the recall. You may be able to have that rear bearing replaced for free at Kia.

HUBCAP & OUTER BEARING REPLACEMENT PROCEDURE: 1. Remove the two (2) cross-tip locating screws on the brake drum.

2. Remove the brake drum.

3. Remove cotter pin and cover set.

4. Remove nut, claw washer, outer bearing and hub assembly.

5. Inspect inner bearing area in both hubs for any sign of moisture, corrosion, grease discoloration or contamination. If "yes" discard entire hub and replace with new assembly. If "no" proceed with outer bearing replacement below: 6. Carefully remove the outer bearing race from the hub. If the hub assembly is damaged then replace the hub assembly as a complete unit. (If inner seal is damaged while removing the outer race replace with new seal.)

7. Clean all contaminated grease from outer bearing cavity of the hub.

8. Install a new outer race into the hub using an appropriate race installation tool.

9. Apply grease MS511-33 WBG2 or equivalent to the hub assembly and the new bearing(s) especially to the shaded areas.

10. Install hub assembly, new pre-greased outer bearing and new claw washer on spindle. (Or alternatively, install entire new hub assembly, as supplied). Ensure bearings are properly seated then tighten hub/spindle nut, torque nut to 20-25 lb-ft (27-33 Nm.) Verify hub spins freely without signs of binding or excessive play.

11. Install new cover set and cotter pin; never reuse the old cotter pin.

12. Install new hub cap with Loctite # 5910(TM) or equivalent sealant to prevent moisture intrusion.

13. Install the rear brake drum using tapered locating screws.

14. Install rear wheels and torque lug nuts to proper specification. (65-79 lb-ft) (88-108 Nm, 9-11 kgm)

15. Lower vehicle.

Dec 30, 2014 | Cars & Trucks

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

How to replace front hub & bearings


You were probably told that because when the wheel bearings go out, a lot of people and shops will just replace the hubs, either new or from a salvage yard, with the bearings already installed (pressed into the hubs). Some models, I think, may not even sell the bearings separate. But since you can buy the bearings alone, that may be the best route for you. That, or the salvage hubs route. If you go with new bearings, you can take off the hubs yourself, and take them with the new bearings to a shop to have them pressed in for a nominal fee. It will save you some serious labor repair costs.
Good luck.

Mar 10, 2012 | 2005 Chevrolet Equinox

1 Answer

What is the foot pounds for the front wheel bearings on a 1995 chrysler cirrus


Hello, If you Chrysler has replaceable wheel bearings and seal. This is the way it goes---pack the wheel bearing with new grease-install the bearing in the wheel nub--install new back wheel seal--coat the axle shaft with grease lightly, thing coat-----install wheel hub on to axle shaft...be careful here don't damage the rear hub seal------------insert front race washer---install axle shaft nut--tighten nut down wheel nut until it is firm with water pump pliers----spin the hub/with tire mounted.
(the wheel and hub will turn but not freely)----take the pliers and back off the axle nut 1/4 turn----now spin the wheel and axle hub, it should spin freely---now if doesn't spin freely---back off the axle nut about 1/16 or 1/32 (or just a little bit)-----now, spin the wheel and hub and if turn freely------------Now grab the top of the wheel/tire and move it back and forth.-----if there is some movement ---try tighten the axle nut just a little little bit, unit the one can barely feel some little movement in the wheel/tire and hub.-----------Now, spin the wheel/tire and hub and it should also turn freely.

If it does----install new and correct size of cotter pin and bent the ends around the axle nut.----

coat the inside of the hub cup with grease. Now, use an rubber or plastic hammer to install the cup on the wheel/tire hub. You are finished with one wheel bearing maintenance. Now do the other side.



I really don't know if you Chrysler Cirrus has replaceable wheel bearing. All the auto/trucks have replaceable hubs, that means that the replacement is total hub with axle shaft, sealed bearings, and seals. This is bolt to each wheel steering hub. This work to remove these one unit hubs.

Four bolts hold the axle hub to the steering hub. Hear is the problem!! it has rusted to the steering hub. Also, these hubs cost more than replacing bearings, races, seals to cool turn of $180 to $250+ I wish you luck in your replacement of wheel bearing on your Chrysler. GB..stewbison

Sep 24, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

I have been told my front wheel bearing is bad. Can replace the just bearing or do I have to replace the whole hub assembly.


the bearing and hub are peened as a assembly and will need to be pressed out of hub carrier on early 05. later models use a one piece bearing that will need to have hub pressed out, then bearing pressed out of carrier both bearings are avalable aftermarket

Oct 23, 2010 | 2005 Mazda 3

1 Answer

Need to change front wheel bearing


Hub and Bearing Removal & Installation NOTE: The removal and installation of the wheel bearing and hub from the steering knuckle is only to be done with the steering knuckle removed from the vehicle
To Remove:
  1. Remove the steering knuckle and hub and bearing assembly.
  2. Remove a wheel lug stud from the hub flange using a C-clamp and Adapter Tool 4150A or equivalent.
  3. Rotate the hub to align the removed lug stud with the notch in the bearing retainer plate. Use a proper C-clamp and adapter tool to press out one of the lug studs 7922eg64.gif

    Rotate the hub in order to remove the lug stud 7922eg65.gif

  4. Rotate the hub so the stud hole is facing away from the brake caliper's lower rail on the steering knuckle.
  5. Install ½ of a Bearing Splitter Tool 1130 or equivalent between the hub and the bearing retainer plate. The threaded hole in this ½ is to be aligned with the caliper rail on the steering knuckle.
  6. Install the remaining pieces of the bearing splitter on the steering knuckle. Hand-tighten the nuts to hold the splitter in place on the knuckle. Proper installation of the bearing splitter 7922eg66.gif

  7. When the bearing splitter is installed, be sure the 3 bolts attaching the bearing retainer plate to the knuckle are contacting the bearing splitter. The bearing retainer plate should not support the knuckle or contact the splitter.
  8. Place the steering knuckle in a hydraulic press, supported by the bearing splitter. Properly support the steering knuckle for hub and bearing removal 7922eg67.gif

  9. Position a driver on the small end of the hub. Using the press, remove the hub from the wheel bearing. The outer bearing race will come out of the wheel bearing when the hub is pressed out of the bearing.
  10. Remove the bearing splitter tool from the knuckle.
  11. Place the knuckle in a press supported by the press block. The blocks must not obstruct the bore in the steering knuckle so the wheel bearing can be pressed out of the knuckle. Place a driver on the outer race of the wheel bearing, and then press the bearing out of the knuckle.
  12. Install the bearing splitter on the hub. The splitter is to be installed on the hub so it is between the flange of the hub and the bearing race on the hub. Place the hub, bearing race and splitter in a press. Use a driver to press the hub out of the bearing race.
To Install:
  1. Use clean, dry cloth to wipe and grease or dirt from the bore of the steering knuckle.
  2. Clean the rust preventative from the replacement wheel bearing using a clean, dry towel.
  3. Place the new wheel bearing into the bore of the steering knuckle. Be sure the bearing is placed squarely into the bore. Place the knuckle in a press with a receiver tool, C-4698-2 or equivalent supporting the steering knuckle. Place a driver tool on the outer race of the wheel bearing. Press the wheel bearing into the steering knuckle until it is fully bottomed in the bore of the steering knuckle. NOTE: Only the original or original equipment replacement bolts should be used to mounting the bearing retainer to the knuckle. If a bolt requires replacement when installing the bearing retainer plate, be sure to get the proper type of replacement.
  4. Install the bearing retainer plate on the steering knuckle. Install the 3 bearing retainer mounting bolts. Torque the bolts to 21 ft-lbs (28 Nm).
  5. Install the removed wheel lug stud into the hub flange.
  6. Place the hub with the lug stud installed, in a press supported by Adapter Tool C-4698-1 or equivalent. Press the wheel lug stud into the hub flange until it is fully seated against the back side on the hub flange.
  7. Place the steering knuckle with the wheel bearing installed, in a press with special Receiver Tool MB-990799 or equivalent supporting the inner race of the wheel bearing. Place the hub in the wheel bearing, making sure it is square with the bearing. Press the hub into the wheel bearing until it is fully bottomed in the wheel bearing.
  8. Install the steering knuckle and the wheel.
  9. Check and/or adjust the front alignment.
prev.gif next.gif

Oct 15, 2010 | 2004 Chrysler PT Cruiser

1 Answer

I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


These are the steps you need to follow for this procedure if you have the proper tools.
  1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
  2. Remove hub and bearing to stub axle retaining nut.
  3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
  4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
  5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

Aug 27, 2010 | 1994 Chrysler LHS

2 Answers

How do i replace the rear wheel bearing on my peugeot 206 1.9hdi year 2002 my rear wheel bearing has gone on my pug206 and i want to know how to fix, replace and repair myself i have bought the rear wheel...


wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Jul 20, 2009 | Peugeot 206 Cars & Trucks

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...