Question about 1985 Chevrolet S-10 Blazer

3 Answers

Get door panel off of a 85 s-10 blazer 2 door

I already figured out all of what you had posted on my own. I need help with the manual type hand crank, it is stuck and won't come off and it has to come off before I can get my panel off. thanks

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 201 Answers

There's a retaining clip on the shaft of the handle. The easiest way to remove this is to buy the special tool for this at your auto parts store - they're realatively cheap, and very quick. You can attempt to remove the clip with a pair of long thin screwdrivers, one to spread each side of the clip, but you'll spend a lot of time cursing it, and probably scratching up the door pad.

Hope this helps!

Posted on Mar 08, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 398 Answers

Thers a tool for these, there is a retaining clip behind the handle you have to "slip" off.You may be able to see it just by pushing against the panel and looking between the panel and the edge of the plastic handle opposite to the way the crank points

Posted on Mar 08, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 149 Answers

It is held on by a small U shaped clip the slides in a groove in the handle. You can use a thin blade flat screw driver or they do make a tool available at a local auto parts store in the "help" section.
Good luck. Dont forget to rate me.

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What color wire goes on what post on 1993 chevy s10 blazer 2 door electric window switch on door wiring


find an auto wrecking yard that has a car like your and ask them if you can look behind the door panel. Then you can see what it should be.

Sep 08, 2014 | Cars & Trucks

1 Answer

Cannot open front passenger door from inside or outside.


From Freeport Have to take panel off and rehook the locking arm it's a buger to do

Jan 10, 2013 | 1991 Chevrolet S-10 Blazer

1 Answer

I have a 1997 chevy blazer 4x4 4.3 engine dome lights will not go off even when car is running,when i loced doors with the automatic button light would come on and would only lock passenger door but w


there's a black box under neath the steering wheel behind the panel unplug it it worked for my blazer i had the same problem it took me 2 months to figure it out i changed all the dome light switched and the fuses so i unplugged the black box under the dash below the steering wheel and it works fine now

Nov 18, 2012 | 1997 Chevrolet Blazer

1 Answer

Right mirror replace


Interior door panel has to come off, then you should be able to figure it out if you can figure out how to get the door panel off. There is a special tool you can get from the HELP section of the parts store. If you have the new mirror in your hand, that will help determine what type fasteners you will be removing.

Jan 04, 2010 | 1991 Buick Century

1 Answer

I can't figure out how to remove the OEM door lock cylinder in my 1994 K1500 Blazer. I can get the handle unfastened, but not removed from the door. Also, can't figure out how to remove the retaining clips...


in order to remove the cylinder, You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.then you have to pull back the seal covering the door and remove the bolts holding the handle, door cylinder, and linkage assembly from inside the door

Aug 18, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Rear windshield wiper connection


You need to open the rear glass from the rear hatch. Look inside where the glass latches to the rear hatch. There is a Phillips head screw that connects the rear inner plastic panel to the rear hatch, remove this screw. Now, in the strap that you use to pull the rear hatch down, there is a torques head screw, that holds this strap to the rear hatch, you need to remove this screw.
Start at one of the outer corners of the inner plastic panel and pull the panel away from the hatch. You will see the upper wiper motor in the right hand corner of the hatch. ther is one connector that is easy to see, you have to pull up on a plastic clip to remove this connector. Look for the rubber hose for the windshield washer fluid, it may be cracked or fallen off the plastic nozzle to the outside of the rear door.

Please the hose back on or replace the hose if it's cracked or damaged by the wiper motor. To install just follow the procedure in revers.
Good luck and hope i made some sense. Keep me posted, be glad to help out.

May 29, 2009 | 1999 Chevrolet Blazer

1 Answer

Can't open back hatch.


it sounds like maybe somthing in the linkage system is disconnected might want to take a look inside use the repair manual to figure out how to take the back door panel off from the inside

repair manual should run you anywhere from $15 to $20 and helps with just about everything

May 19, 2009 | 2000 Chevrolet Blazer

1 Answer

95 blazer, front driver window motor broken need to get window up


When removing the door panel, you need to remove all of the screws first. Then pull the door panel off. There should be screws around the edges or the door panel, and 1-2 screw on the door handle(on the inside). Then pop the door panel off, if the blazer has electric windows and locks you have to disconect them first, if it doesnt have power locks and windows, you have to take the window crank off,there should be a screw in the center of that. Unscrew the door lock and pull up. If it doesnt have them locks then you have to disconect it from inside the door panel

Nov 30, 2008 | 1995 Chevrolet Blazer

1 Answer

Chevy blazer 2w drive 2 door-rear gate wont open


you will need to try to remove the rear door panel on the tail gate or pry it away its not easy because of hidden screws the manually pull the linkage

Aug 16, 2008 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...