Question about 2005 Chrysler Pacifica

1 Answer

Head lamps not working after one bulb was replaced

We changed one hid lamps that burnt out in my chrysler pacifica, and now they wont work at all. the high beams work, but not the daytime running lights and regular headlights.

Posted by on

  • appleknock Mar 11, 2009

    2007 PAC Touring. Without warning the exterior running lights for front & rear (left side) are inop, while brake and turn signals work fine...



    Heard prob is in fuse box (IPM) up front, checked mini fuses, none blown, but how do you tell if the relay or clear larger fuses are blown?

  • Anonymous Mar 22, 2014

    video to change right high beam lamp

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 106 Answers

There are both a fuse and a relay for boyt sides.On your vehicle they are in the fuse box out in the engine compartment.there is allso a large amp fuse for the whole system should be in the same box.I would check these first.Hope this helps.

Posted on Mar 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my name is Larry I have a 1998 Pontiac sunfire & my problem that I have is I have low beam. But no high beam.


It's probably the switch , but testing to know for sure is alwasy a good idea .

Headlamps Inoperative - High Beams
Step
Action
Value(s)
Yes
No
1
Did you perform the Daytime Running Lamps (DRL) System Check?
--
YES - Go to Step 2
NO - Go to Daytime Running Lights (DRL) System Check
2
Disconnect the turn/hazard headlamp switch connector C1.
Connect a fused jumper between terminal B of the turn/hazard headlamp switch assembly harness connector C1 and ground.
Do the high beam headlamps operate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the turn/hazard headlamp switch assembly.
Did you complete the repair?
--
Go to Daytime Running Lights (DRL) System Check
--
4
Repair the open in CKT 1200 between the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?

Daytime Running Lights (DRL) System Check
Step
Action
Normal Result(s)
Abnormal Result(s)*
1
Turn the headlamp switch to the HEAD position.
Turn the headlamp dimmer switch to the LOW position.
The low beam headlamps are ON.
The high beam headlamps are OFF.
Headlamps Inoperative - Low Beams
2
Turn the headlamp switch to the HIGH position.
The high beam headlamps are ON.
The high beam indicator is ON.
The low beam headlamps are OFF.
Headlamps Inoperative - High Beams
3
Turn the headlamp switch OFF.
Turn the ignition to ON.
Disengage the parking brake.
The high beam headlamps come ON at a reduced intensity in approximately 30 seconds.
Daytime Running Lamps (DRL) Inoperative, Headlamp Switch Operates Normally
* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.

Jan 13, 2017 | 1998 Pontiac Sunfire

1 Answer

After changing transmisson only one head light works windows wont roll down ac doesnt work and windshield wipers dont work. any help?


Could be the harness was smashed when the transmission was put on. Maybe the engine and transmission ground to body wasn't connected. head light is a bulb or bad wire. The Wipers are a bad motor or ground, The widows, if they worked before, is a bad ground.

Aug 07, 2015 | 2006 Chrysler Pacifica

2 Answers

All of my running lights and blinkers work and high beams but no low beams on my 1997 Chevrolet TahoeA


Headlamps Inoperative - Low Beams

Step

Action

Value(s)

Yes

No

DEFINITION: This diagnostic procedure should only be used if the high beam headlamps are operating properly and the low beams are inoperative.

1

Did you perform the Headlights System Check?
--
Go to Step 2
Go to Headlight System Check

2

  1. Turn the headlamp and panel dimmer switch to the ON position.
  2. Move the headlamp dimmer switch to the LOW position.
  3. Backprobe the headlamp dimmer switch connector with a J 35616-200 from cavity A to ground.

Does the test lamp light?
--
Go to Step 3
Go to Step 5

3

  1. Remove the daytime running lamp relay.
  2. Connect a J 35616-200 at cavity G5 to ground.

Does the test lamp light?
--
Go to Step 4
Go to Step 6

4

  1. Re-install the daytime running lamp relay.
  2. Backprobe cavity B at the high/low beam headlamp with the headlamp dimmer switch in the LOW position.

Does the test lamp light?
--
Go to Step 7
Go to Step 8

5

Replace the headlamp dimmer switch.

Is the repair complete?
--
Go to Headlight System Check
--

6

Repair the open in CKT 359 (PPL) between the headlamp dimmer switch and the daytime running lamp relay.

Is the repair complete?
--
Go to Headlight System Check
--

7

Replace the high/low beam headlamps.

Is the repair complete?
--
Go to Headlight System Check
--

8

  1. Inspect for an open in CKT 12 (TAN) between the daytime running lamp relay and S120, repair as necessary.
  2. Replace the daytime running lamp relay if no open was found in CKT 12 (TAN) between the daytime running lamp relay and S120.

Is the repair complete?
--
Go to Headlight System Check
--

Jul 24, 2015 | Chevrolet Cars & Trucks

2 Answers

How do I get the low beams to run automatically whenever driving instead of flickering?




if you did it yourself and did not use factory lights or ballast then it could be a voltage detection problem. If you did use factory parts then the headlight switch may have failed by coincidence. also check connections at HL plugs and or switch. ???????????

Nov 13, 2014 | 2001 Audi TT

3 Answers

Replaced low beam light buls in 2005 pacifica crysler and lights still wont work. What is the problem


MAKE/MODELS: MODEL/BUILD YEARS:
Chrysler/Pacifica 2005
MANUFACTURER: DaimlerChrysler Corporation
NHTSA CAMPAIGN ID NUMBER: 05V066000 RECALL DATE: March 01, 2005
COMPONENT: Exterior Lighting: Headlights
POTENTIAL NUMBER OF UNITS AFFECTED: 43180
SUMMARY:
Certain sport utility vehicles equipped with Halogen headlamps may experience an intermittent and eventual total loss of headlamp function.
CONSEQUENCE:
The head lights may not operate properly which could result in intermittent or no headlight function. This could impair a driver's visibility, increasing the risk of a crash.
REMEDY:
Dealers will inspect, and replace if necessary, the wiring harness and low beam bulb on both headlamp assemblies. The manufacturer has not yet provided an owner notification schedule for this campaign. Owners should contact DaimlerChrysler at 1-800-853-1403.
NOTES:
DaimlerChrysler Recall No. E04. Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-327-4236

Nov 17, 2011 | 2005 Chrysler Pacifica

1 Answer

2002 Dodge Caravan headlamps: one works on dim the other works on high beam but not together. Also only one daytime running lamp.


Your van has dual diligent headlamp bulbs, that means each headlight has one bulb that serves as high beam and low beam. What has most likely happened is on one side the low beam filament has burnt out, and on the other side the high beam filiment has burnt out. The daytime running lights are just the high beam filament running on reduced power, so if the high beam doesn't work on one side, that same side will have no daytime running light. Replace both headlamp bulbs with matching, good quality bulbs.

Mar 06, 2011 | 2002 Dodge Grand Caravan

2 Answers

My head light has turned Pink!


If you have HID headlights, the pinkish color is a sign that the bulb is getting ready to go out. HID bulbs are expensive, so you will need to do some shopping around to find the best deal. My research indicates a relatively high degree of difficulty in changing the bulbs. You will probably need a repair manual to find out what's involved and whether or not you want to tackle the job yourself. Good luck to you.

Feb 07, 2011 | 2005 Chrysler 300

2 Answers

Only hi beams work ...no low beams . Lamps and fuses are good. Replaced relay, no change. Keep reading about ground wire from lights can not find it


The wiring schematic changes drasticly depending on whether your vehicle is equipped with daytime running lamps or not. However, both systems have one thing in common...the low beams and the high beams get their grounds from the same place. If the high beams are working correctly, the ground is not your problem. The most common causes of low beams not working and high beams working are the multifunction switch (or as Toyota calls it: "Combination Switch") and if your vehicle has daytime running lamps, the Daytime Running Lamp Module could be the problem.

Dec 02, 2010 | 2001 Toyota Tacoma

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

448 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

66126 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...