Question about 2002 Dodge Ram Maxi

1 Answer

Clutch not disengaging when stopped at a stop sign for a period o

2002 Dodge Diesel 6 sp HO clutch is not disengaging when stopped at a stop light for a period of time. The last few days I have had problems with my clutch at signal lights when I have to wait a little longer than usual to start moving again......I can not then even get it out of gear and it starts jumping ahead. I checked the fluid in the hyrdaulic brakes reservoir and it is up to par. I checked underneath and there are no leaks coming out from anywhere.

Leo

Posted by on

  • chilcotin Mar 08, 2009

    Polarcycle....can you tell me if this is inside or outside the bellhousing?



  • chilcotin Mar 25, 2009

    That was the problem...and we got it fixed. Could have done it myself easily if I had been at home where my tools are to use. It was the bottom one but they said it all had to be replaced.

    thanks again for your help.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

It is either your clutch master bleeding down, or your slave cylinder is leaking. Should be able to check inside the truck for a leak from behind the clutch master, the slave is by the trans.

Posted on Mar 08, 2009

  • Eldric Venne
    Eldric Venne Mar 08, 2009

    It should be located outside the trans, but not 100% on that. It sounds like you need a new clutch master cylinder if you don't see any leaks. Just be sure to put the truck in neutral before you come to a stop.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge caravan shuts off at stop sign or red light


Either a brake light switch or torque converter clutch solenoid needs to be replaced.the vehicles talk converter clutch is not disengaging when activated by the brake light switch. Therefore one of these two items is defective.

Jan 30, 2015 | 2003 Dodge Caravan

1 Answer

A/C kicks off and recirc light comes on


AC clutch is going to the dogs. Or the high pressure switch is giving it up. This is assuming AC belt is not slipping. Also check the system charge as it may need recharging.

Apr 03, 2013 | 2006 Toyota Sienna

1 Answer

2007 Dodge 2500 5.9 diesel. When you turn on AC you can see clutch try and engauge and after 3-4 tries it stops. No AC. If drive around for a while AC starts to work after engine heats up?


Working same problem today on my 2006 Mega Cab Diesel. 2 possibilities. Either the compressor clutch coil is going bad ( totally integrated power module tries to engage it a couple of times, senses the coil resistance is wrong and shuts down) or the TIPM (Total Integrated Power Module) is bad. I'm leaning toward clutch on compressor but still have testing to do to isolate. Could be both, but I doubt it. New TIPM is about $900 it appears from what I read. New compressor is cheaper. May be able to replace just the clutch coil for even less but reading mixed results. Good luck.

Aug 05, 2011 | 2006 Dodge Ram 2500

2 Answers

2004 Dodge Durango Clutch fan issue, clutch fan disengages after 1-2 minutes after cold startup then engages everytime you come to a stop and start again, temp is just below halfway, I have already...


I just replaced my 2004 durango fan clutch and the new fan clutch will not disengage. The fan keeps runnning very loud i have replaced the new one already still doing the samething. Do i have a bad clutch or do i need to have the vehicle idle looked at

Jul 12, 2010 | 2004 Dodge Durango

2 Answers

The engine is starting to chug when at a stop


have u checked the fuel filter, how many kilomiters on it could be a fuel pump, or ignition censior

Jun 04, 2010 | 2002 Saturn L-Series

1 Answer

On a 1985 Ford F250 diesel, with the 4 speed


I would replace fluid and filter. At least the fluid. Old fluid has bad temperature range protection and the inter cooler doesn't help cool the lines much.

Nov 23, 2009 | 1985 Ford F 250

1 Answer

02 dodge 2500 clutch not releasing


An hydraulic clutch line can be bled. There should be a bleeder screw on the cylinder at the end of the line running from the master clutch-cylinder.

Charlie

Aug 14, 2009 | 2002 Dodge Ram Maxi

1 Answer

2002 dodge diesel 2500 5 Speed....... Clutch will


if master cylinder and slave cylinder.is good and have brake fluid is in system and no leaks.problem is in the clutch and pressure plate.

Jun 10, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
2002 Dodge Ram Maxi Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...