Question about 2004 Dodge SRT-4

1 Answer

None of the gears on my 2004 SRT-4 work, but the clutch still seems to work. What can be wrong?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Can you put it into gear easy, if so it could be your shifting rod

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does the clutch slip intermittently on my Audi A4 2009 Diesel in high gears


Agreed. The clutch disk is likely worn. The pressure plate is self adjusting so there is no adjustment available on stock Audi pressure plates or indeed in most pressure plates.

Another possible cause is a leaking rear main engine seal that is allowing engine oil to seep and then be thrown around the bell housing and work its way onto the flywheel/clutch/pressure plate.

Test you clutch in 3-4 gear acceleration from a slow speed...if the engine speed flares faster than the car accelerates, you have a worn/bad clutch.

Mar 22, 2015 | 2004 Audi A4

1 Answer

Noticed that the revs would build too quickly and did not match the 2004 Rav4 speed in higher gears. 1st gear seems OK. If I accelerate gradually there are no problems. So I'm guessing I need my clutch...


You are exactly right. The clutch is going out. The cable is an automatic adjusting cable. So there is no adjustment. It will require a new clutch.

Jan 24, 2011 | 2004 Toyota RAV4

1 Answer

Car wont move!


Sounds like the trans input shaft may be broken.If the input shaft, which is connected to the clutch, is not transmitting rotation to the inside of the trans then what you describe will occur.

May 15, 2009 | 2005 Dodge SRT-4

1 Answer

When going throught the gears forward sometimes it takes more muscle to change particularly 3 to 4 or 4 to 5 ..... sometimes it is easy to change gear and sometimes it seems to take more effort ....kind of...


try double clutching(come out of 3rd then push clutch twice b-4 going to 4th. if this works your clutch slave may be weak or pressure plate is worn. Try shifting from 1st-3rd if engine revs like your in neutral replace clutch. when going 1st-3rd engine should catch and cause vehicle to buck&stumble. (check level of clutch master cylinder)

Nov 26, 2008 | Toyota Paseo Cars & Trucks

3 Answers

My turbo won't boost its starts to shake and pull back


Check out all your air hoses and clamps and check the turbo itself to make sure it spins freely. (Engine not running)

Nov 11, 2008 | 2004 Dodge SRT-4

1 Answer

2004 Dodge SRT-4 keeps coding out


What code number? It could have a wiring short or open to the PCM or to ground. Cam could be out of time, check the timing belt.

Aug 16, 2008 | 2004 Dodge SRT-4

1 Answer

04 Dodge SRT 4 crankshaft sensor


The Crankshaft Position Sensor is located directly next to the starter.
  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Aug 15, 2008 | 2004 Dodge SRT-4

Not finding what you are looking for?
2004 Dodge SRT-4 Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...