Question about 2001 Isuzu Rodeo

1 Answer

P1220 code need the trouble tree to diagnose componate.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 96 Answers


Posted on Mar 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Anti theft system override for 2004 builk Rainier

There is no override ! Have it checked for code's and then diagnose it with factory trouble tree chart !

Dec 07, 2016 | 2004 Buick Rainier

1 Answer

1999 elantra catalyst monitor, evaporative system monitor and 02 sensor monitor not ready fail inspection

Get the codes,diagnose using the codes

Need trouble charts & component test

Not replacing parts & hoping for results

Feb 12, 2013 | Cars & Trucks

1 Answer

Abs 2004 chevy tahoe

No one can diagnose that, or guess from the internet

You need to use the codes & trouble charts, to
component test the ABS Braking System

Sep 08, 2012 | 2004 Chevrolet Tahoe

1 Answer

Code 41 trouble tree

code 41 fuel injector failure

Sep 08, 2012 | 1992 Mitsubishi Diamante

1 Answer

P1220 series throttle control system malfunction

Hi there:
DTC P1220 - Throttle Position (TP) Sensor 2 Circuit

This code indicate a open circuit on the throttle sensor, maybe an idea to wire the sensor direct to ECU, bypass harness and any problems it might have; if it works you then know your problem is in the harness.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | 2002 Volvo S40

1 Answer

Need trouble codes for 1993 Cadillac F31 F47

prev.gif next.gif Reading Codes OBD-I Systems Fig. 1: Diagnostic trouble codes — 4.5L engine 84204010.jpg
Fig. 2: Diagnostic trouble codes — 4.9L engine 84204277.jpg
Fig. 3: Diagnostic trouble codes — 4.6L engine 84204442.jpg
Listings of the trouble codes for the various engine control systems covered in this manual are located in this section. Remember that a code only points to the faulty circuit NOT necessarily to a faulty component. Loose, damaged or corroded connections may contribute to a fault code on a circuit when the sensor or component is operating properly. Be sure that the components are faulty before replacing them, especially the expensive ones. The Assembly Line Diagnostic Link (ALDL) connector or Data Link Connector (DLC) may be located under the dash and sometimes covered with a plastic cover labeled DIAGNOSTIC CONNECTOR.
  1. On all 1990–95 models the diagnostic trouble codes can be read by grounding test terminal B. The terminal is most easily grounded by connecting it to terminal A (internal ECM ground). This is the terminal to the right of terminal B on the top row of the ALDL connector.
  2. Once the terminals have been connected, the ignition switch must be moved to the ON position with the engine not running.
  3. The Service Engine Soon or Check Engine light should be flashing. If it isn't, turn the ignition OFF and remove the jumper wire. Turn the ignition ON and confirm that light is now on. If it is not, replace the bulb and try again. If the bulb still will not light, or if it does not flash with the test terminal grounded, the system should be diagnosed by an experienced driveability technician. If the light is OK, proceed as follows.
  4. The code(s) stored in memory may be read through counting the flashes of the dashboard warning lamp. The dash warning lamp should begin to flash Code 12. The code will display as one flash, a pause and two flashes. Code 12 is not a fault code. It is used as a system acknowledgment or handshake code; its presence indicates that the PCM can communicate as requested. Code 12 is used to begin every diagnostic sequence. Some vehicles also use Code 12 after all diagnostic codes have been sent.
  5. After Code 12 has been transmitted 3 times, the fault codes, if any, will each be transmitted 3 times. The codes are stored and transmitted in numeric order from lowest to highest. NOTE: The order of codes in the memory does not indicate the order of occurrence.
  6. If there are no codes stored, but a driveability or emissions problem is evident, the system should be diagnosed by an experienced driveability technician.
  7. If one or more codes are stored, record them. Refer to the applicable Diagnostic Code chart in this section.
  8. Switch the ignition OFF when finished with code retrieval or scan tool readings. NOTE: After making repairs, clear the trouble codes and operate the vehicle to see if it will reset, indicating further problems.

Jun 28, 2010 | 1993 Cadillac DeVille

1 Answer

I have a PO340 that keeps coming up intermittantly. I replaced the cam sensor with no help.

there is a trouble tree that is supposed to be used to diagnose this. It not always what it seems thats why we have thousands of dollars of equipment. We just dont throw parts on. The dealer may have a PCM update for this code but you never know if you take short cuts.

Nov 21, 2009 | 2003 Nissan Altima

1 Answer

Code p1945

The code is code-p1945-leak-detection-pump This usually indicates a short or falure of the pump.

This is not the type of thing that can be diagnosed without a scanner and a trouble tree. I stongly recomend you take it to an expert.

Hope this helps.

Oct 01, 2009 | 2002 Chrysler Town & Country

1 Answer

I have an 88 buick LeSabre/ vin "C"/ 3.8 with a trouble code 26. It only comes on going up hill

Hi! I have enclosed 3 trouble trees for you. The code being stored is a quad driver error. Quad(which means 4)drivers control up to 4 things. They are located in the engine control module. They provide ground for the items that they control. This could mean a component that the driver controls could be bad or the computer itself. Hope this helps you!deb334a.gif911608a.gif925db0e.gif

Sep 17, 2009 | 1988 Buick LeSabre

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

Related Topics:

1,079 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides