Question about 2005 Dodge Dakota

1 Answer

2002 f250 ford 7.3 power stroke cam sensor location?

Posted by on

  • Anonymous May 12, 2009

    my problem is I can start my truck 2000 f250 7.3 power stroke this was running and run out of diesel and I put diesel again and run again but the engine stop and I can't get start again any body have some idea what is going on.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try “” or your local library for diagrams and step by step instructions.

Posted on Mar 08, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why would my abs light keep coming on after I have changed it. I have a 1998 ford f250 power stroke diesle

So the light was on and you changed the bulb to fix it? You may have a ABS Wheel Speed Sensor bad. the one located in the rear axle is common to go bad.

Sep 03, 2010 | Ford F-250 Cars & Trucks

1 Answer

2002 F250 Super Duty SuperCab: replace crankshaft sensor...

Also called the cam sensor on the 7.3. It is located in the front of the engine just above the harmonic balancer just to the right. 10mm Bolt holds it in. Easier to get to from below going up behind radiator. Disconnect plug then remove bolt then wiggle it out. Make sure oring came with it and then replace with a black one. Some people say to use a blue one but i have had no trouble with a black one from Autozone.

May 07, 2010 | 2002 Ford F250 Super Duty SuperCab

2 Answers


The 7.3 power stroke is not tha bad sheesh its actually pretty simple ok let me ask some questions here ok lets start simple when cranking does the needle on the tach move to approx. 5-600 ? if not more than likely its a cam sensor in which case there is actually a recall from ford they will fix it free.... yes I said free :) if not my second guess would be the Idm they were notorious for getting moisture in them btw IDM stands for injector driver module and you can find a good reman unit online for 200 "use google" if you have a friend with a high end scanner hook up and watch engine rpm there and also do a "buzz test" no buzz = idm fail another easy thing to do is open the drain on the fuel filter bowl and turn the key on and crank for 1 sec is there fuel shooting out ? if there isnt check fuel pump well that about covers it good luck please let us know whats up :)

Feb 15, 2010 | 1999 Ford F250 Regular Cab

1 Answer

Have a light on in the upper right hand side of dash with and arow throw it 2002 ford f250

It's the airflow sensor for your air filter. Change the filter and reset the sensor located on the air filter box.

Feb 14, 2010 | 2002 Ford F250 Super Duty SuperCab

1 Answer

2002 Ford F250 7.3 200,000 plus miles running great but after running for about 30 minutes shut off it won't fire for about 20 minutes replaced Cam sensor where else do I look Larry

You should be getting the check engine light on. Take the truck to Autozone or similar business for a free computer scan (they will be happy to sell you any needed parts). The crankshaft sensor is the other critical sensor that controls fuel injection and ignition. The scan results should point that out if it is a problem. Hope this gets you running again!

Jan 23, 2010 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Where is the fuel pump located on a 1995 Ford F250 Power stroke diesel?

in the fuel tank if its a exsened cab itt might have a helper pumpon the frame rail too

Nov 28, 2009 | 1995 Ford F250

1 Answer

Truck stalls after running for a sensor changed already and oil pressure sensor changed also...fuel pump is workin fine....what else can i do?

you stated you changed the cam pos. sensor, meaning it must be a 7.3 or 6.0 turbo diesel. These engines are extremely sensitive to low fluid levels and failing sensors, first i will suggest for you to check and top off all fluids wich include antifreeze and oil above all. if those are within range, proceed to check the injector control pressure sensor located in the driver side of the engine towards the front.

Nov 18, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Po720 location

the speed sensor is in the rear differential

Nov 25, 2008 | 2002 Ford F250 Super Duty SuperCab

1 Answer

2002 Ford F250 7.3 diesel will not start

could be the cam sensor has gone out, there was a recall for this

Jul 12, 2008 | 2002 Ford F250 Super Duty SuperCab

Not finding what you are looking for?
2005 Dodge Dakota Logo

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides